Cisco Systems AS5800 - page 69

debug vrm error

Voice over IP for the Cisco AS5800 69

This error message shows that there is no buffer left in the pool for the VTSP to send a message to

the DSP. <Number> int his output referst o the number of times the VRM ran out of buffer space.

- vrm_vtsp_get_packet: no buffers <number>

This error message notifies the VRM of a DSP alarm:

- vrm_vtsp_indicate_alarm : alarm_type <value> slot <slot#> tag <tag#> chan <chan#>

Possible values for the alarm are as follows:

•FATAL_ERROR = 0x01

•MEMORY_ERROR = 0x02

•BUFFER_ERROR = 0x04

•DOWNLOAD_ERROR = 0x08

•CHECKSUM_ERROR = 0x10

This eror message shows that the DSP sent a defective message:

- vrm msg offset too big tag <tag#> vchan <chan#>

Table8 expains the field contained in the previous example.

This error message indicates that an alarm message was received from the VFC/DSP and was

successfully sent to the VTSP:

- vrm_msg_process_alarm_msg for <slot#>.<tag#>.<chan#> , state=<value>

Possible state values are as follows:

•0 = RESET

•1 = ADMINDOWN

•2 = CORE_READY

•3 = CODEC_READY

•4 = VOICE_IDLE

•5 = FAX_IDLE

•6 = VOICE_READY

•7 = FAX_READY

•8= DTMF_READY

Table8 debug vrm error Field Descriptions

Field Description

slot# Slot in the Cisco AS5800 where the VFC is installed.

tag# DSP number. Possible values for this field are 1 to 96.

chan# Channel number. Possible values for this field are 1 and 2.

Contents

Main Voice over IP for the Cisco AS5800 Feature Overview Benefits Two-Stage-Dial Toll Bypass PSTN Voice-Traffic and Fax-Traffic Off load Universally Accessible Voice-Mail and Fax-Mail Services Additional Benefits Restrictions Related Features and Technologies Related Documents Supported Platforms Supported Standards, MIBs, and RFCs Prerequisites Configuration Tasks Configuring IP Networks for Real-Time Voice Traffic Configuring Voice Ports Page Fine-Tuning ISDN Voice Ports To fine-tune ISDN voice ports, use the following commands beginning in privileged EXEC mode: Page Configuring Dial Peers Inbound versus Outbound Dial Peers Configuring POTS Peers Outbound Dialing on POTS Peers Direct Inward Dial for POTS Peers Distinguishing Voice and Modem Calls on the Cisco AS5800 Configuring VoIP Peers Verifying Dial Peer Configuration Troubleshooting Tips Configuring the Cisco AS5800 as an H.323 Gateway Verifying Gateway Interface Configuration Configuring the Cisco AS5800 for Interactive Voice Response Available IVR Scripts Configuring IVR Verifying IVR Configuration Configuration Example Configuration Example 20 Cisco IOS Release 12.0(7)T Configuring the Cisco 3640 as a Gatekeeper Configuring the Cisco 2600 as a Gateway Configuring the Cisco AS5800 as a Gateway Command Reference New Commands Page codec Page dtmf-relay Page port Cisco 2600/3600 Series Router Cisco MC3810 Cisco AS5300 Access Server Cisco AS5800 Access Server Command Mode Example show csm Page The following is sample output from the Cisco AS5800 for the show csm voice command: Table1 explains the fields contained in both of these examples. Page Page Page Page show voice port For the Cisco MC3810: For the Cisco AS5300 Access Server: For the Cisco AS5800 Universal Access Server: Command Mode Command Reference 38 Cisco IOS Release 12.0(7)T show voice port Voice over IP for the Cisco AS5800 39 Table2 explains the fields in the sample output. Page The following is sample output from the Cisco AS5800 for the show voice port command: Table3 explains the fields in the sample output. Page show vrm active_calls Table4 explains the fields in the sample output. Page show vrm vdevices Command Reference 48 Cisco IOS Release 12.0(7)T Table5 explains the fields in the sample output. Page Page Table6 explains the fields in the sample output. Page Page Page test vrm busyout Page test vrm reset test vrm unbusyout Page voice-port Page Page Debug Commands debug vrm control debug vrm control Voice over IP for the Cisco AS5800 65 Format of the Send messages is as follows: Format for the Receive messages is as follows: Table7 describes the fields in previous example. debug vrm error Page Page Page debug vrm inout Glossary G