| 4) | When a desirable station is tuned in, press | |||||
|
| the SHIFT button 22 to cancel PS/AS mode | |||||
|
| and press the preset button to which the sta- | |||||
English |
| tion is to be stored. | |||||
| * The preset scanning is canceled and you can | ||||||
|
| listen to the station. | |||||
| Preset selection | ||||||
| 1) | Press the BND button 13 to select a band. | |||||
Owner’s | 2) | Press one of the Preset buttons 16 to 21 to | |||||
Note: | |||||||
|
| select the stored station. | |||||
Guide | • In PS/AS mode, do not perform the preset selec- | ||||||
| |||||||
| tion (excluding the preset scanning). | ||||||
| In PS/AS mode, when the Preset button 17 is | ||||||
| pressed, the auto storing starts and all the stored | ||||||
| stations are cleared. | ||||||
| ISR memory | ||||||
| If an AM or FM station is stored in the ISR but- | ||||||
| ton, it can be directly tuned in by pressing the | ||||||
| ISR button from any other mode. | ||||||
| 1) | Press the BND button 13 to select a band. | |||||
| 2) | Press the Preset buttons 16 to 21 or the ENT | |||||
|
| button 11 to tune in to a station you want to | |||||
|
| store. | |||||
| 3) | Press and hold the ISR button 24 for about 2 | |||||
|
| seconds. | |||||
|
| When a beep sounds, the display turns to the | |||||
|
| ISR (Instant Station Recall) display and the | |||||
|
| frequency is stored. | |||||
| 4) | Press the ISR button 24 to return to the pre- | |||||
|
| vious mode. | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Calling the station with the ISR button
1)In any mode, pressing the ISR button 24 allows you to tune in to the stored station.
*When the ISR is functioning, the ISR display appears.
*The default ISR setting is 87.9 MHz.
2)To cancel the ISR function, press the ISR but- ton 24 or FUNC button 12 . The ISR function is canceled and the previous mode returns.
Area change
When you listen to the radio outside the U.S., use this function.
Switchable frequency setting
This car stereo is initially set to tune in frequen- cy intervals of 10 kHz for AM and 200 kHz for FM, the standard calibrations in the U.S. When using the unit outside the U.S., use the following procedure to switch the frequency range.
The table below lists the frequency specifica- tions for the U.S. and other countries.
|
| Initial Setting | New Setting | |
|
| (U.S. standard) | (outside U.S.) | |
|
|
|
| |
| Frequency | 10 kHz | 9 kHz | |
AM | spacing |
|
| |
Frequency | 530 to 1710 kHz | 531 to 1629 kHz | ||
| ||||
| range |
|
| |
| Frequency | 200 kHz | 50 kHz | |
FM | spacing |
|
| |
Frequency | 87.9 to 107.9 MHz | 87.5 to 108 MHz | ||
| ||||
| range |
|
|
Changing area
Depending on whether you use the unit in the U.S. or outside the U.S., switch the area as fol- lows:
1)Press the ADJ button 10 to go to the CON- FIGURATION display.
2)Slide the Up/Down button 11 to (up) or
(down) and move the cursor to “AREA.”
3)Slide the Up/Down button 11 to (right) to switch the area (between in the U.S. and out- side the U.S.).
4)Press the ADJ button 10 to return to the pre- vious mode.
*The new setting returns to the initial setting.
18