Feature Set-up, Caller ID Display | Clarity C600 specification

Feature Set-up

CALLER ID DISPLAY

Set-up Mode

C600 handset goes into setup mode automatic when battery is connected.

Or press and hold MODE button for 3 seconds to enter setup mode. If there is no input within 30 seconds, the language will be set to the last selected one and go back to standby mode.

Caller ID Screen

Setting Language

1.After entering setup mode, the LCD display will show SEL LANGUAGE and then 1.ENG 2.SPA alternately with a tick mark against the selected language.

2.Press 1, 2 OR 3 button once to change the language.The tick mark will move against the new selection.

3.Press UP (▲) to go to the next menu.

Setting Contrast

There are 3 contrast levels and the default is set to level 2.

1.After setting the language, press UP(▲) key to begin setting contrast.

2.The LCD display will show LCD CONTRAST and 1 2 3.

3.Press the 1, 2 or 3 key to change the level.The current selected level will be highlighted.

4.Press the UP(▲) or DOWN (▼) button to go to the next menu.

Setting AREA CODE 1

1.After setting Contrast, press UP (▲) button to set Area Code 1.

2.The LCD display will show “AREA CODE

1and XYZ with X digit blinking.

3.Enter the area code number using the numeric keys on the handset.

4.Press the UP (▲) or DOWN (▼) button to go to the next menu.

Setting AREA CODE 2

1.After setting Area Code 1, press UP (▲) button to set Area Code 2.

2.The LCD display will show AREA CODE 2 and XYZ with X digit blinking.

3.Enter the area code number using the numeric keys on the handset.

4.Press the UP (▲) or DOWN (▼) button to go to the next menu.

12

Image 12

Clarity C600 manual Feature Set-up, Caller ID Display

Contents

GHz Cordless Telephone with Caller ID Table of Contents Important Safety Instructions Read and understand all instructions Safety Instructions For Batteries Never install telephone wiring during a lightning stormUse caution when installing or modifying telephone lines Designed for wet locations Features DEL/Channel Button DEL/CH Volume Control Talk Button TalkMm Headset Jack Key Pad Neckloop Jack Handset Charging Contacts Telephone Base Base Side/End/Bottom Installation Connecting Your TelephoneTable/Desktop Installation Getting Started Wall Mounting Instructions Lift the bases antenna to a vertical positionPlace handset in the cradle to begin initial charging Battery Installation To Install a New BatteryHandset Battery Charging Low Battery Headset Jack Belt ClipHearing Aid Compatibility Feature Set-up Caller ID Display Setting LDS Code Setting Easy ModeSetting Voicemail no Setting Message Waiting ON/OFF Telephone Base Boost ON/OFF Switch Battery BackupPulse/Tone Flash Telephone Operations Temporary Tone Lighted Key PadPage/Handset Locator Channel Operation Memory Storage Memory OperationsReview Phonebook Information Adding a Phonebook Number Dialing a Phonebook Entry Deleting a Stored NumberDeleting All Stored Numbers No action Adding the Emergency Number Dialing the Emergency NumberDeleting the Emergency Number Visual Message Waiting Indicator Vmwi Caller ID OperationsCaller ID Information Saving Caller ID Information to Phonebook Callback from Caller ID Information Digits without a 1 prefixArea Code + 7 digits without a 1 prefix Digits with a 1 prefix Delete Caller ID Information Delete One Caller ID InformationDeleting All Caller ID Information Maintenance and Care Avoid dropping or knocking the unit Troubleshooting Phone does not ring when you receive a callUnit will not operate/no dial tone Few devices Phone Will Not Hold Charge Difficulty in Placing or Receiving Calls Regulatory Compliance Part 68 of FCC Rules Information Customer-Owned Coin/Credit Card Phones Part 15 of FCC Rules Information Industry Canada Technical Specifications Equipment Warranty and Service How to Obtain Warranty Service United StatesCanada Fax 514