Setup Menu
NOTE: In order to output a Dolby Digital signal, the amplifier or external device that the unit is hooked up to must have Dolby Digital, DTS and MPEG decoding.
Trouble Shooting
Should your DVD player develop a problem, please check below before requesting service:
Specification
Power supply | DC 9.0V 2A (AC adapter TERMINAL) |
SPDIF/PCM: Select this item when the DVD player is connected with a
OFF: When this item is selected, all digital coaxial and optical outputs are turned off.
--Custom Setup--
Press the UP/DOWN button to highlight the desired Custom item (Parental Ctrl, Password, Angle Mark, Default), and press ENTER to confirm.
:Move | :Select SETUP:Out |
A). Parental Ctrl
There are eight levels of Parental Control. Level one opens discs to people of all ages. Level eight is suitable only for adults.
To change the parental control setting, a
B). Password
Move the cursor to the PASSWORD prompt and press ENTER. Input the password 8888 if it is the first use. After confirmation, you will be required to input a new
WARNING:
Please keep a copy of the new password in a safe place. Otherwise, you will not be able to change the Parental Control.
Please remember your password, as the DEFAULT setting will revert everything BUT the PASSWORD and Parental Control to the factory defaults.
C). Angle Mark
Symptom
No power
Does not play
No Picture
Picture noisy/ distorted
No sound or sound output not complete
Remote control does not work
Check and Action
1.Make sure the unit has been powered on manually.
2.Check if the power cord has been properly connected to the power outlet.
3.Make sure the battery pack is fully charged.
1.No disc, load a disc.
2.Disc has been loaded upside down. Place the disc with the label side up.
3.Disc's rating level is higher than the player's setting.
4.Disc is incorrect type for the player.
5.Disc is damaged or dirty. Clean the disc or try another one.
6.Moisture may be condensed inside the player. Remove the disc and leave the unit power on for one or two hours.
1.Check if the TV set has been powered on. Use TV remote to select AV signal for DVD rather than broadcast.
2.Check if the system connection is proper and secure.
3.Check if the connection cables are damaged.
4.Clean the disc.
1.Disc is damaged or dirty. Clean the disc or try another one.
2.Reset the color system of the TV set.
3.Make sure the DVD player is not connected through a VCR, cable or satellite dish.
1.Check if the TV and amplifier have been switched on and correctly set.
2.Check if the TV and amplifier system connections are secured.
3.Press AUDIO button to select other audio tracks of the disc.
4.Check if the MUTE function of the TV or amplifier has been activated.
5.There will be no sound output during REVERSE PLAY/PAUSE/SLOW and
SEARCH.
1.Make sure the POWER button on the unit has been turned on manually.
2.Remove the obstacles between the remote control and the player.
3.Point the remote control towards the remote sensor on the player.
4.Check if the batteries of the remote control have been loaded with correct polarities.
5.Replace the batteries of the remote control.
Power consumption | <=9w |
|
|
|
Signal system | NTSC |
|
|
|
Video output | 1+0.2V | |||
Audio output | 1.5 Vrms (1 KHz, 0dB), 3.5 mm mini jack x1 | |||
|
|
|
|
|
Coaxial Output | 3.5mm | mini | jack x 1 |
|
|
|
|
| |
Earphone terminal | 3.5mm stereo | mini jack x1 | ||
Signal /Noise ratio(audio) | 90dB typical |
|
| |
Dynamic range(audio) | 90dB typical |
|
| |
Panel size | 5 inch (4:3) |
|
| |
Resolution | 320(H) x 240 (V) (QVGA) Pixels | |||
Laser | Wavelength 650 nm | |||
Operating conditions | Temperature: 0 | c to 35 c. Operation status : Horizontal | ||
Dimensions | 165x152x50mm (Main Unit & Batt.) | |||
|
|
| ||
Weight | 887.5g | (Main Unit & Batt. ) | ||
Choose between ON and OFF.
The default setting is ON.
When the Angle Mark function is ON, an icon will be displayed on screen if the disc has multiple angle shots available for viewing.
Press ANGLE on the remote control to enjoy these scenes.
D). Default
This function allows you to change the player back to the factory default settings. All settings will be changed back to the original settings except the Password and Parental Control.
.17.
Malfunction | Should the player develop a malfunction, unplug the player for 30 minutes. After |
| that, power on the player and the restore function should reset the player. |
.18.
.19.
