| SPRAY NOZZLE SELECTION |
|
|
PRE-START PREPARATION
Before starting the pressure washer, check for loose or missing parts and for any damage which may have occurred during shipment.
PUMP PREPERATION
The pump is shipped with a shipping plug, this will need to be replaced with the vent plug that is supplied.
START-UP PROCEDURE
1.Make sure water supply is connected and turned on.
2.Release gun safety if locked.
3.To allow air to escape from the hose, squeeze trigger on the gun until there is a steady stream of water coming from the nozzle.
4.Remove any dirt or foreign matter from the gun outlet and the male connector of the wand.
5.Insert the nozzle wand into the gun wand and tighten the fitting securely.
6.Place the throttle in the HI position.
STARTING THE ENGINE
1.Check oil and fuel level.
2.Adjust choke prime as necessary.
3.Set the engine switch to the “ON” position.
4.Squeeze trigger on pressure washer to release pressure while pulling on the engine starter rope with a fast steady pull. Pressure may otherwise build up making starting the unit difficult.
5.As the engine warms up, readjust the choke.
GXR2424 SPECIFICATIONS
Maximum Inlet Pressure | . . . . . . . .Up to 90 PSIG |
RPM | . . . . . . . . . . .3600 RPM |
Temperature of Pumped Fluids | . . . . . . . . . . .Up to 80°F |
Inlet Ports | . . . . . . . . .(2) 1/2” BSP |
Discharge Ports | . . . . . . . . .(1) 3/8” BSP |
Weight | . . . . . . . . . . . . . . .9 lbs. |
Crankcase oil Capacity | . . . . . . . . . . . .4.7 fl. oz. |
Pump oil | .SAE 30W Nondetergent |
Consult the factory for special requirements that must be met if the pump is to operate beyond one or more of the limits
specified above.
Following is information concerning the four nozzles provided with your pressure washer.
NOTE: The force of the spray on the surface you are clean- ing increases as you move closer to the surface.
0° High Pressure (Red): The water stream discharged is very aggressive. Use with extreme caution to prevent damage to the sur- face being cleaned or injury to persons or animals.
15° High Pressure (Yellow): This is the nozzle used for most cleaning applications. It provides wide coverage and a powerful water stream.
40° High Pressure (White): This nozzle is used for cleaning with a wider coverage over a larger area with a
powerful water stream.
65° Low Pressure (Black): Provides low pressure spray and a wide coverage. Used primarily when operating the chemical injector to apply chemicals.
GXR2424 SERIES TORQUE SPECIFICATIONS
Item | Description | Torque Amount |
10 | Socket Bolt | 100 |
40 | Stud Bolt | 150 |
|
|
|
GXR2424 SERIES REPAIR KITS
Oil Seal Kit (9468)
Order # 0057960
Regulator Repair Kit (9493)
Order # 0057961
Plunger Packing Kit (9465)
Order # 0057958
Valve Assembly Kit (9466)
Order # 0057959
Gasoline Flange Kit (9103)
Order # 0057957
Wobble Plate 6.3 Degree Kit (17047)
Order # 0057964
Flange Adapting Kit (17026)
Order # 0057963
OPERATING CONNECTIONS
HIGH PRESSURE HOSE
Attach the high pressure hose to the fitting located on the front side of the side panel. Only Coleman Powermate Pressure Washer high pressure hoses should be used.
WATER CONNECTION
Before connecting the inlet hose to the unit, run water
through the garden hose (not supplied) to flush out any foreign matter. The inlet hose will be connected to the fitting located on the back of the side panel.
INLET HOSE
HIGH PRESSURE HOSE
English | 5 |
