Manuals / Compaq / Computer Equipment / Laptop

Compaq 515, 511, 510 manual Remove the system board

Models: 515 511 510

1 156

Download 156 pages 39.04 Kb

Page 80

Remove the system board:

Removal and replacement procedures

Remove the system board:

1.Disconnect the fan cable 1 from the system board.

2.Remove the Phillips PM2.5×4.0 screw 2 that secures the system board to the base enclosure.

3.Release the RJ-11 connector 1 from the clip built into the base enclosure.

4.Flex the left side of the base enclosure 2 until the external monitor connector 3 is clear of the opening of the base enclosure.

5.Lift the rear edge of the system board 4 until it rests at an angle.

6.Remove the system board 5 by sliding it back.

Reverse this procedure to install the system board.

Maintenance and Service Guide

4–37

Image 80

Compaq 515, 511, 510 manual Remove the system board

Contents

Compaq 510 Notebook PC Maintenance and Service GuideCompaq 516 Notebook PC Compaq 515 Notebook PC Compaq 511 Notebook PC Copyright 2009 Hewlett-Packard Development Company, L.P First Edition June Document Part Number534271-001Safety warning notice Contents 4 Removal and replacement procedures1 Product description 2 External component identification 3 Illustrated parts catalogContents 5 Computer Setup6 Specifications 7 Screw listing 8 Backup and recovery9 Connector pin assignments Index 10Power cord set requirements11Recycling Product description Product description Supports the following configurations at 800 MHz and 667 MHz continued Compaq Compaq Compaq Preinstalled Restore MediaServiceability End-user replaceable parts CertifiedDisplay components External component identificationTop components Speaker Buttons, switch, and speaker Keys Lights Pointing devices Description Front componentsComponent Description Right-side componentsComponent Left-side components Bottom components If you replace the module and then receive a warning message, removeService tag Illustrated parts catalogIllustrated parts catalog Computer major componentsMaintenance and Service Guide Switch cover includes power button board and cable Item Description538451-001 Spare Part NumberFor use in Japan GL system board use only on computer models equipped with a graphics subsystem with Battery Item DescriptionWLAN module 802.11a/b/g/n WLAN module for use with all computer modelsIllustrated parts catalog Item Description Memory modulesPlastics Kit 1 ExpressCard slot bezel 2 Wireless module compartment cover5 RJ-11 connector cover 6 Optical drive bay bezel 3 Hard drive cover includes three captive screws, secured by C-clipsDisplay assembly subcomponents Mass storage devices Miscellaneous parts Power cordsDescription Spare part numberDescription Sequential part number listingSpare part number the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan Spare part number DescriptionSpare part number DescriptionSpare part number DescriptionSpare part number DescriptionRemoval and replacement procedures Preliminary replacement requirementsService considerations Cables and connectorsElectrostatic discharge damage Grounding guidelinesDrive handling Packaging and transporting guidelines Workstation guidelines Equipment guidelinesComponent replacement procedures Service tagBattery Computer feetRemove the battery 2. Slide the battery release latches 1 to release the battery3. Remove the battery 2 from the computer Removal and replacement proceduresHard drive Remove the hard drive 7. Remove the hard drive 4 from the hard drive bay Reverse this procedure to reassemble and install the hard drive Removal and replacement proceduresMaintenance and Service Guide b. Lift the bracket 2 straight up to remove it from the hard driveWLAN module the Central African Republic, Chad, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, the Peoples Republic of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa Ä CAUTION To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support Reverse this procedure to install the WLAN module Memory module Remove the memory module Optical drive a. Position the optical drive with the rear toward you Keyboard and switch cover For use in country or regionSpare part number For use in country or regionRemoval and replacement procedures 3. Turn the computer display-side up with the front toward you 10. Remove the keyboard Speaker Display assembly DescriptionSpare part numberRemove the display assembly 1. Close the computer 8. Disconnect the webcam module cable 1 from the system board 538426-001-for use only on computer models equipped with a webcam 16. Disconnect the webcam module cable 2 from the webcam module 20. Remove the eight Phillips PM2.0×3.0 screws 1 that secure the hinges to the display panel 30. Release the tabs 3 built into the display enclosure shielding c. Keyboard and switch cover see “Keyboard and switch cover” on page e. Display assembly see “Display assembly” on pageTop cover a. Hard drive see “Hard drive” on page3. Turn the computer right-side up with the front toward you Bluetooth module f. Top cover see “Top cover” on pagec. Keyboard and switch cover see “Keyboard and switch cover” on page e. Display assembly see “Display assembly” on pageRemove the Bluetooth module and cable 1. Disconnect the Bluetooth module cable 1 from the system board3. Remove the Bluetooth module and cable Reverse this procedure to install the Bluetooth moduleRTC battery see “RTC battery” on page System boardWLAN module see “WLAN module” on page Memory modules see “Memory module” on pageRemove the system board g. System board see “System board” on page c. Keyboard and switch cover see “Keyboard and switch cover” on pagee. Display assembly see “Display assembly” on page a. Hard drive see “Hard drive” on page2. Remove the fan Reverse this procedure to install the fan Removal and replacement proceduresMaintenance and Service Guide Remove the fanRTC battery c. Keyboard and switch cover see “Keyboard and switch cover” on pagee. Display assembly see “Display assembly” on page a. Hard drive see “Hard drive” on pageRemove the RTC battery 2. Remove the RTC battery from the socket on the system boardReverse this procedure to install the RTC battery Removal and replacement proceduresModem module c. Keyboard and switch cover see “Keyboard and switch cover” on pagee. Display assembly see “Display assembly” on page a. Hard drive see “Hard drive” on pageRemove the modem module Heat sink c. Keyboard and switch cover see “Keyboard and switch cover” on pagee. Display assembly see “Display assembly” on page a. Hard drive see “Hard drive” on pageRemove the heat sink 5. Remove the heat sink Reverse this procedure to install the heat sink Modem module cable h. Heat sink see “Heat sink” on pagec. Keyboard and switch cover see “Keyboard and switch cover” on page e. Display assembly see “Display assembly” on pageProcessor c. Keyboard and switch cover see “Keyboard and switch cover” on pagee. Display assembly see “Display assembly” on page a. Hard drive see “Hard drive” on pageRemove the processor Computer Setup Computer Setup for computer models equipped with an AMD processorStarting Computer Setup Using Computer SetupRestoring factory settings in Computer Setup Computer SetupComputer Setup menus File MenuSelect To do thisDiagnostics Menu Security MenuIdentification information for the computer and the batteries in the Hard Disk Test-Runs a comprehensive self-test on any hard drive inSystem Configuration Menu Use of a USB keyboard in Computer Setup even when a WindowsTo do this System Configuration menu continuedSelect Computer Setup for computer models equipped with an Intel processor Starting Computer SetupUsing Computer Setup Navigating and selecting in Computer SetupFile Menu Computer Setup menusRestoring factory settings in Computer Setup Diagnostics Menu Security MenuSelect To do thisTo do this System Configuration MenuSelect Specifications Computer specifications14.0-in display specifications SpecificationsHard drive specifications SpecificationsDVD±RW and CD-RW SuperMulti Double-Layer Drive specifications Access timeApplicable disc ReadDVD-ROM Drive specifications Access timeApplicable disc ReadDMA System function System DMA specificationsHardware System memory map specifications SizeMemory address System functionSystem function System interrupt specificationsHardware IRQ I/O address hex System I/O address specificationsSystem function shipping configuration System function shipping configuration I/O address hexPhillips PM2.0×6.0 captive screw Where usedScrew listing Screw listing Phillips PM2.5×11.0 captive screwMaintenance and Service Guide Phillips PM3.0×4.0 screw Black Phillips PM2.5×4.0 screw Where used 2 screws that secure the WLAN module to the computerWhere used 2 screws that secure the speaker to the top cover Maintenance and Service GuideWhere used 2 screws that secure the modem module to the system board Silver Phillips PM2.5×4.0 screw Maintenance and Service GuideColor QuantitySlotted Torx T8M2.5×8.0 screw Where used1 Two screws that secure the switch cover to the computer 2 Six screws that secure the top cover to the computerPhillips PM2.0×3.0 screw Phillips PM2.0×3.0 screw Phillips PM2.0×2.0 broadhead screw Maintenance and Service Guide2 Two screws that secure the top cover to the computer Phillips PM2.0×3.0 broadhead screwWhere used Phillips PM2.5×8.0 screw Where usedMaintenance and Service Guide 1 One screw that secures the optical drive to the computerPhillips PM2.0×4.0 screw Where used One screw that secures the top cover to the base enclosureMaintenance and Service Guide Phillips PM2.5×6.0 screwWhere used 4 screws that secure the display assembly to the computer Where used 2 screws that secure the top cover to the base enclosure Where used 2 screws that secure the fan to the base enclosureMaintenance and Service Guide Screw listingPhillips PM2.5×5.0 screw Maintenance and Service GuidePhillips PM2.5×9.0 captive screw 7-18 Maintenance and Service GuideScrew listing Phillips PM2.0×5.0 captive screw 7-20 Maintenance and Service GuideScrew listing Overview Backup and recoveryBackup and recovery in Windows Vista 1. Select Start All Programs Maintenance Backup and Restore Center Backing up your informationPerforming a recovery Using the Windows recovery tools1. Click Start All Programs Maintenance Backup and Restore Center 4. Select Repair your computer6. Select Repair your computer Using f11Using a Windows Vista operating system DVD purchased separately Backup and recovery in Windows XP 1. Click Start All Programs Accessories System Tools BackupOverview Backing up your informationRecovering your information Recovering the operating system and programs3. Click Restore files and settings, and then click Next Performing a recoveryAudio-out headphone Connector pin assignmentsAudio-in microphone External monitor Connector pin assignmentsRJ-11 modem RJ-45 networkSignal SignalMaintenance and Service Guide Universal Serial BusSignal Power cord set requirements Requirements for all countries and regionsRequirements for specific countries and regions Country/regionAccredited agency Applicable note numberDisplay BatteryRecycling Perform the following steps to disassemble the display assembly Maintenance and Service Guide3. Remove the display bezel Recycling6. Remove the display panel assembly 2 from the display enclosure 10. Remove the display panel frame 2 from the display panel 18. Remove the backlight from the backlight frame 16. Turn the display panel upside down17. Remove the backlight frame from the display panel Maintenance and Service Guide 19. Disconnect the display cable 1 from the LCD panel21. Release the LCD panel 3 from the display rear panel 23. Remove the LCD panel 24. Recycle the LCD panel and backlightIndex Index Index-2Page