Manuals / Compaq / Computer Equipment / Laptop

Compaq 515 System Configuration Menu, Use of a USB keyboard in Computer Setup even when a Windows

Models: 515 511 510

1 156

Download 156 pages 39.04 Kb

Page 98

System Configuration Menu

Computer Setup

System Configuration Menu

✎Some of the listed System Configuration options may not be supported by your computer.

Select	To do this

Language	Change the Computer Setup language.

Boot Options	■ Set a Startup Menu delay (in seconds).
	■ Enable/disable Custom Logo (disabled by default).
	■ Enable/disable Display Diagnostic URL (enabled by default).
	■ Enable/disable CD-ROM boot (enabled by default).
	■ Enable/disable SD Card boot (enabled by default).
	■ Enable/disable floppy boot (enabled by default).
	■ Enable/disable PXE Internal NIC boot (disabled by default).
	■ Set the Express Boot Popup delay in seconds.
	■ Set the boot order.

Device Configurations	■ Enable/disable USB legacy support (enabled by default). When
	enabled, USB legacy support allows the following:
	❐ Use of a USB keyboard in Computer Setup even when a Windows
	operating system is not running.
	❐ Startup from bootable USB devices, including a hard drive,
	diskette drive, or optical drive connected by a USB port to the
	computer.
	■ Enable/disable fan always on while connected to an AC outlet
	(disabled by default).
	■ SATA (Serial Advanced Technology Attachment) device mode. The
	following options are available:
	❐ AHCI (Advanced Host Controller Interface)
	❐ IDE (Integrated Drive Electronics)
	✎ Availability of the options above varies by computer model.
	■ Enable/Disable Unified Extensible Firmware Interface (UEFI) mode
	(disabled by default).

	(Continued)

Maintenance and Service Guide

5–5

Image 98

Compaq 515, 511, 510 manual System Configuration Menu, Use of a USB keyboard in Computer Setup even when a Windows

Contents

Compaq 510 Notebook PC Maintenance and Service GuideCompaq 516 Notebook PC Compaq 515 Notebook PC Compaq 511 Notebook PC Copyright 2009 Hewlett-Packard Development Company, L.P First Edition June Document Part Number534271-001Safety warning notice 1 Product description 2 External component identification Contents4 Removal and replacement procedures 3 Illustrated parts catalogContents 5 Computer Setup6 Specifications 7 Screw listing 8 Backup and recovery9 Connector pin assignments Index 10Power cord set requirements11Recycling Product description Product description Supports the following configurations at 800 MHz and 667 MHz continued Compaq Compaq Compaq Serviceability End-user replaceable parts PreinstalledRestore Media CertifiedDisplay components External component identificationTop components Speaker Buttons, switch, and speaker Keys Lights Pointing devices Description Front componentsComponent Description Right-side componentsComponent Left-side components Bottom components If you replace the module and then receive a warning message, removeService tag Illustrated parts catalogIllustrated parts catalog Computer major componentsMaintenance and Service Guide 538451-001 Switch cover includes power button board and cableItem Description Spare Part NumberFor use in Japan GL system board use only on computer models equipped with a graphics subsystem with WLAN module BatteryItem Description 802.11a/b/g/n WLAN module for use with all computer modelsIllustrated parts catalog Item Description Memory modules5 RJ-11 connector cover 6 Optical drive bay bezel Plastics Kit1 ExpressCard slot bezel 2 Wireless module compartment cover 3 Hard drive cover includes three captive screws, secured by C-clipsDisplay assembly subcomponents Mass storage devices Description Miscellaneous partsPower cords Spare part numberDescription Sequential part number listingSpare part number the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan Spare part number DescriptionSpare part number DescriptionSpare part number DescriptionSpare part number DescriptionService considerations Removal and replacement proceduresPreliminary replacement requirements Cables and connectorsElectrostatic discharge damage Grounding guidelinesDrive handling Packaging and transporting guidelines Workstation guidelines Equipment guidelinesComponent replacement procedures Service tagBattery Computer feet3. Remove the battery 2 from the computer Remove the battery2. Slide the battery release latches 1 to release the battery Removal and replacement proceduresHard drive Remove the hard drive 7. Remove the hard drive 4 from the hard drive bay Maintenance and Service Guide Reverse this procedure to reassemble and install the hard driveRemoval and replacement procedures b. Lift the bracket 2 straight up to remove it from the hard driveWLAN module the Central African Republic, Chad, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, the Peoples Republic of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa Ä CAUTION To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support Reverse this procedure to install the WLAN module Memory module Remove the memory module Optical drive a. Position the optical drive with the rear toward you Spare part number Keyboard and switch coverFor use in country or region For use in country or regionRemoval and replacement procedures 3. Turn the computer display-side up with the front toward you 10. Remove the keyboard Speaker Display assembly DescriptionSpare part numberRemove the display assembly 1. Close the computer 8. Disconnect the webcam module cable 1 from the system board 538426-001-for use only on computer models equipped with a webcam 16. Disconnect the webcam module cable 2 from the webcam module 20. Remove the eight Phillips PM2.0×3.0 screws 1 that secure the hinges to the display panel 30. Release the tabs 3 built into the display enclosure shielding Top cover c. Keyboard and switch cover see “Keyboard and switch cover” on pagee. Display assembly see “Display assembly” on page a. Hard drive see “Hard drive” on page3. Turn the computer right-side up with the front toward you c. Keyboard and switch cover see “Keyboard and switch cover” on page Bluetooth modulef. Top cover see “Top cover” on page e. Display assembly see “Display assembly” on page3. Remove the Bluetooth module and cable Remove the Bluetooth module and cable1. Disconnect the Bluetooth module cable 1 from the system board Reverse this procedure to install the Bluetooth moduleWLAN module see “WLAN module” on page RTC battery see “RTC battery” on pageSystem board Memory modules see “Memory module” on pageRemove the system board e. Display assembly see “Display assembly” on page g. System board see “System board” on pagec. Keyboard and switch cover see “Keyboard and switch cover” on page a. Hard drive see “Hard drive” on pageMaintenance and Service Guide 2. Remove the fan Reverse this procedure to install the fanRemoval and replacement procedures Remove the fane. Display assembly see “Display assembly” on page RTC batteryc. Keyboard and switch cover see “Keyboard and switch cover” on page a. Hard drive see “Hard drive” on pageReverse this procedure to install the RTC battery Remove the RTC battery2. Remove the RTC battery from the socket on the system board Removal and replacement procedurese. Display assembly see “Display assembly” on page Modem modulec. Keyboard and switch cover see “Keyboard and switch cover” on page a. Hard drive see “Hard drive” on pageRemove the modem module e. Display assembly see “Display assembly” on page Heat sinkc. Keyboard and switch cover see “Keyboard and switch cover” on page a. Hard drive see “Hard drive” on pageRemove the heat sink 5. Remove the heat sink Reverse this procedure to install the heat sink c. Keyboard and switch cover see “Keyboard and switch cover” on page Modem module cableh. Heat sink see “Heat sink” on page e. Display assembly see “Display assembly” on pagee. Display assembly see “Display assembly” on page Processorc. Keyboard and switch cover see “Keyboard and switch cover” on page a. Hard drive see “Hard drive” on pageRemove the processor Starting Computer Setup Computer SetupComputer Setup for computer models equipped with an AMD processor Using Computer SetupRestoring factory settings in Computer Setup Computer SetupSelect Computer Setup menusFile Menu To do thisIdentification information for the computer and the batteries in the Diagnostics MenuSecurity Menu Hard Disk Test-Runs a comprehensive self-test on any hard drive inSystem Configuration Menu Use of a USB keyboard in Computer Setup even when a WindowsTo do this System Configuration menu continuedSelect Using Computer Setup Computer Setup for computer models equipped with an Intel processorStarting Computer Setup Navigating and selecting in Computer SetupFile Menu Computer Setup menusRestoring factory settings in Computer Setup Select Diagnostics MenuSecurity Menu To do thisTo do this System Configuration MenuSelect Specifications Computer specifications14.0-in display specifications SpecificationsHard drive specifications SpecificationsApplicable disc DVD±RW and CD-RW SuperMulti Double-Layer Drive specificationsAccess time ReadApplicable disc DVD-ROM Drive specificationsAccess time ReadDMA System function System DMA specificationsHardware Memory address System memory map specificationsSize System functionSystem function System interrupt specificationsHardware IRQ I/O address hex System I/O address specificationsSystem function shipping configuration System function shipping configuration I/O address hexPhillips PM2.0×6.0 captive screw Where usedScrew listing Screw listing Phillips PM2.5×11.0 captive screwMaintenance and Service Guide Phillips PM3.0×4.0 screw Where used 2 screws that secure the speaker to the top cover Black Phillips PM2.5×4.0 screwWhere used 2 screws that secure the WLAN module to the computer Maintenance and Service GuideWhere used 2 screws that secure the modem module to the system board Color Silver Phillips PM2.5×4.0 screwMaintenance and Service Guide Quantity1 Two screws that secure the switch cover to the computer Slotted Torx T8M2.5×8.0 screwWhere used 2 Six screws that secure the top cover to the computerPhillips PM2.0×3.0 screw Phillips PM2.0×3.0 screw Phillips PM2.0×2.0 broadhead screw Maintenance and Service Guide2 Two screws that secure the top cover to the computer Phillips PM2.0×3.0 broadhead screwWhere used Maintenance and Service Guide Phillips PM2.5×8.0 screwWhere used 1 One screw that secures the optical drive to the computerPhillips PM2.0×4.0 screw Where used One screw that secures the top cover to the base enclosureMaintenance and Service Guide Phillips PM2.5×6.0 screwWhere used 4 screws that secure the display assembly to the computer Maintenance and Service Guide Where used 2 screws that secure the top cover to the base enclosureWhere used 2 screws that secure the fan to the base enclosure Screw listingPhillips PM2.5×5.0 screw Maintenance and Service GuidePhillips PM2.5×9.0 captive screw 7-18 Maintenance and Service GuideScrew listing Phillips PM2.0×5.0 captive screw 7-20 Maintenance and Service GuideScrew listing Overview Backup and recoveryBackup and recovery in Windows Vista 1. Select Start All Programs Maintenance Backup and Restore Center Backing up your information1. Click Start All Programs Maintenance Backup and Restore Center Performing a recoveryUsing the Windows recovery tools 4. Select Repair your computer6. Select Repair your computer Using f11Using a Windows Vista operating system DVD purchased separately Overview Backup and recovery in Windows XP1. Click Start All Programs Accessories System Tools Backup Backing up your information3. Click Restore files and settings, and then click Next Recovering your informationRecovering the operating system and programs Performing a recoveryAudio-out headphone Connector pin assignmentsAudio-in microphone External monitor Connector pin assignmentsSignal RJ-11 modemRJ-45 network SignalMaintenance and Service Guide Universal Serial BusSignal Power cord set requirements Requirements for all countries and regionsAccredited agency Requirements for specific countries and regionsCountry/region Applicable note numberDisplay BatteryRecycling 3. Remove the display bezel Perform the following steps to disassemble the display assemblyMaintenance and Service Guide Recycling6. Remove the display panel assembly 2 from the display enclosure 10. Remove the display panel frame 2 from the display panel 18. Remove the backlight from the backlight frame 16. Turn the display panel upside down17. Remove the backlight frame from the display panel 21. Release the LCD panel 3 from the display rear panel Maintenance and Service Guide19. Disconnect the display cable 1 from the LCD panel 23. Remove the LCD panel 24. Recycle the LCD panel and backlightIndex Index Index-2Page