Contec SEH-9450-LAS - page 90

8. BIOS Setup

SEH-9450-LAS 83

DISK BOOT failure

INSERT SYSTEM DISK AND PRESS ENTER

No boot device was found. This could mean that either a boot drive was not detected or the drive does

not contain proper system boot files. Insert a system disk into Drive A: and press <Enter>. If you

assumed the system would boot from the hard drive, make sure the controller is inserted correctly and all

cables are properly attached. Also be sure the disk is formatted as a boot device. Then reboot the

system.

Diskette drives or types mismatch error

RUN SETUP

Type of diskette drive installed in the system is different from the CMOS definition. Run Setup to

reconfigure the drive type correctly.

Display switch is set incorrectly

Display switch on the motherboard can be set to either monochrome or color. This indicates the switch

is set to a different setting than indicated in Setup. Determine which setting is correct, and then either

turn off the system and change the jumper, or enter Setup and change the VIDEO selection.

Display type has changed since last BOOT

Since last powering off the system, the display adapter has been changed. You must configure the

system for the new display type.

EISA configuration checksum error

PLEASE RUN EISA CONFIGURATION UTILITY

The EISA non-volatile RAM checksum is incorrect or cannot correctly read the EISA slot. This can

indicate either the EISA non-volatile memory has become corrupt or the slot has been configured

incorrectly. Also be sure the card is in-stalled firmly in the slot.

EISA configuration is not complete

PLEASE RUN EISA CONFIGURATION UTILITY

The slot configuration information stored in the EISA non-volatile memory is incomplete.

Note: When either of these errors appear, the system will boot in ISA mode,

which allows you to run the EISA Configuration Utility.

Error encountered initializing hard drive

Hard drive cannot be initialized. Be sure the adapter is installed correctly and all cables are correctly

and firmly attached. Also be sure the correct hard drive type is selected in Setup.

Error initializing hard disk controller

Cannot initialize controller. Make sure the cord is correctly and firmly installed in the bus. Be sure the

correct hard drive type is selected in Setup. Also check to see if any jumper needs to be set correctly on

the hard drive.

Contents

Main SBC Series Single Board Computer Half-size PICMG 1.3 with LAN, Audio, SATA SEH-9450-LAS Users Manual CONTEC CO.,LTD. Check Your Package Copyright Trademarks Caution about Battery Table of Contents 1. INTRODUCTION 1 2. SYSTEM REFERENCE 5 3. HARDWARE INSTALLATIONS 11 4. JUMPER SETTING 25 5. CPU BOARD RESOURCES 29 6. WATCH-DOG-TIMER (WDT) SETTING 31 7. HARDWARE MONITOR 35 8. BIOS SETUP 37 Page 1. Introduction About the SBC Features Customer Support Web Site Limited One Year Warranty How to Obtain Service Liability Safety Precautions Safety Information DANGER WARNI N G CAUTION Environments Inspection Storage Disposal 2. System Reference 2. System Reference Specification Table 2.1. Functional Specifications < 1 / 2 > 2. System Reference 6 SEH-9450-LAS Table 2.1. Functional Specifications < 2 / 2 > Power Management Features Power Requirements Power Consumption Connector & Jumper Location Page 2. System Reference 10 SEH-9450-LAS Block Diagram Figure 2.2. Block Diagram 3. Hardware Installations CPU Installation: Main Memory Installation: DIMM1, DIMM2 3. Hardware Installations SEH-9450-LAS 13 Audio Connector: AUDIO1 21 This connector connects the Audio jack cable. Table 3.2. Audio Connector 10 9 2 LINE-OUT-L 1 LINE-OUT-R Serial Port Connector: COM1 / COM2 RS-422 / RS-485 specifications CPU FAN Connector: FAN1 System FAN Connector: FAN2 Front Panel Connector: FP1 Power Switch (Power BT) Reset Switch (RESET) Power LED Hard drive activity LED (IDE ACT) IDE port Connector: IDE1 Keyboard / Mouse Connector: KB/MS1 Adapter connector for Giga LAN: LAN1 3. Hardware Installations SEH-9450-LAS 19 LVDS LCD Connector: LVDS1 / LVDS2 1 2 20 19 20 +12V 19 +12V VDD: +3.3V LCD power out (1A Max.) 3. Hardware Installations Mini PCI type III expansion socket: PCI1 Power supply Connector: PWR1 Serial ATA Connector: SATA1 / SATA2 Serial Digital Video Output: SDVO1 USB Connector: USB1, USB2, USB3 VGA Connector: VGA1 4. Jumper Setting Clear CMOS Content & BIOS setting cancel: JBAT1 CF Master / Slave selector: JP1 RS-232/422/485 Selector: JCOM1 Page Page 5. CPU Board Resources System address map Compatibility Area Memory Segment PCI Routing Information Page 6. Watch-Dog-Timer (WDT) Setting Introduction } Page Page Page 7. Hardware Monitor Hardware Monitor Temperature Voltage Page 8. BIOS Setup Introduction Starting Setup Using Setup Getting Help In Case of Problems A Final Note About Setup Main Menu Setup Items Page Page 8. BIOS Setup 42 SEH-9450-LAS Main Menu Selections 8. BIOS Setup SEH-9450-LAS 43 IDE Adapters Page CPU Feature Hard Disk Boot Priority Virus Warning Page 8. BIOS Setup SEH-9450-LAS 49 8. BIOS Setup 50 SEH-9450-LAS 8. BIOS Setup SEH-9450-LAS 51 Advanced Chipset Features Setup 8. BIOS Setup SEH-9450-LAS 53 8. BIOS Setup 54 SEH-9450-LAS PCI Express Root Port Function VGA setting Integrated Peripherals OnChip IDE Device 8. BIOS Setup Enabled SEH-9450-LAS 59 8. BIOS Setup 60 SEH-9450-LAS 8. BIOS Setup SEH-9450-LAS 61 On Chip Serial ATA Setting Table 8.10. On Chip Serial ATA setting Selections Page Onboard Device 8. BIOS Setup 64 SEH-9450-LAS Super IO Device Power Management Setup 8. BIOS Setup SEH-9450-LAS 67 8. BIOS Setup 68 SEH-9450-LAS 8. BIOS Setup SEH-9450-LAS 69 8. BIOS Setup 70 SEH-9450-LAS Page PnP/PCI Configuration Setup Page IRQ n Resources Page 8. BIOS Setup 76 SEH-9450-LAS PCI Express relative items Page 8. BIOS Setup SEH-9450-LAS 79 Table 8.16. PC Health Status Selections Page Defaults Menu Supervisor /User Password Setting Exit Selecting POST Messages POST Beep Error Messages Page Page Page Page 8. BIOS Setup SEH-9450-LAS 87 POST Codes 8. BIOS Setup 88 SEH-9450-LAS 8. BIOS Setup SEH-9450-LAS 89 8. BIOS Setup 90 SEH-9450-LAS 8. BIOS Setup SEH-9450-LAS 91 SEH-9450-LAS Users Manual CONTEC CO.,LTD.