Engineruns,but Transmissionreleaseleversin PUSH MoveleverstoDRIVEpositions.
rider | will not | positions. |
|
|
|
|
|
|
| ||||
drive. |
|
|
| Drive | belt slips, | Clean or replace belt as necessary, | |||||||
|
|
|
| Belt | is broken, |
| Replace | drive belt, | Contact Sears Parts & Repair, | ||||
|
|
|
| Parking | brake | is not fully released, | Contact | Sears Parts & Repair, | |||||
Rider | drive | belt | Pulleys or belt | greasy or oily, | Clean as required, |
|
| ||||||
slips. |
|
|
| Belt stretched | or worn. | Replace | belt. | Contact Sears Parts & Repair. | |||||
|
|
|
| ||||||||||
Parking | brake | Parking | brake | is incorrectly adjusted, | See | Service | & Adjustments | Section, | |||||
will not | hold. |
|
|
|
|
|
|
|
|
|
| ||
Rider | steers | or | Improper | tire inflation. | See | Maintenance | Section. |
| |||||
handles | poorly. | Steering | linkage is loose, | Check and tighten | any loose connections, | ||||||||
|
|
|
| ||||||||||
Rider | tracks | to | Ground speed adj. knobs not adjusted, | See SPEED | BALANCING | ADJUSTMENT in Service & | |||||||
one side. |
|
|
|
|
| Adjustments | section, |
| |||||
Troubleshooting | the | Mower |
|
|
|
|
|
|
|
| |||||
PROBLEM |
| CAUSE |
|
|
|
| REMEDY |
|
|
|
|
| |||
Mower cutting | Cutting height motor screw dirty or requires | Thoroughly | clean and | lubricate cutting height motor | |||||||||||
height | does | not | lube. |
|
|
|
| screw, |
|
|
|
|
| ||
adjust. |
|
| Cutting | height | linkage | disconnected, | Check that | mower | linkage is connected, | ||||||
Mower cut is |
| Rider tires | not inflated | equally or properly. | See | Maintenance | Section. |
| |||||||
uneven. |
| Mower | not leveled properly, | See | "Mower Leveling" | in Service & Adjustments, | |||||||||
Mower | cut is | Engine | speed | too slow, | Always set engine | speed to FAST when mowing, | |||||||||
rough | looking. | Ground | speed | too fast, | Decrease | ground | speed, |
| |||||||
|
|
| Blades | are dull, |
| Sharpen | or replace blades, See Maintenance | ||||||||
|
|
|
|
|
|
|
| Section, |
|
|
|
|
| ||
|
|
| Mower | drive belt slipping because it is oily or Clean or replace belt | as necessary, |
| |||||||||
|
|
| worn. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Blades | not properly fastened to arbors. | See | "Check/Replace | Mower Blades" | in Maintenance | |||||||
|
|
|
|
|
|
|
| Section. |
|
|
|
|
| ||
Engine | stalls |
| Engine | speed | too slow. | Always set engine | speed to FAST when mowing. | ||||||||
easily | with |
| Ground | speed | too fast, | Decrease |
| Ground | Speed, |
| |||||
mower | engaged. |
|
| ||||||||||||
Cutting height set too low. | Cut tall grass at maximum cutting height during first | ||||||||||||||
|
|
| |||||||||||||
|
|
|
|
|
|
|
| pass, |
|
|
|
|
| ||
|
|
| Underside | of mower deck dirty, | Remove | mower deck and clean underside, | |||||||||
|
|
| Discharge | chute jamming with cut grass, | Cut grass with discharge pointing toward previously | ||||||||||
|
|
|
|
|
|
|
| cut area, |
|
|
|
|
| ||
Excessive |
| Blade mounting bolts | are loose, | Tighten to |
| ||||||||||
mower |
|
| Mower blades, arbors, or pulleys are bent, | Check and replace as necessary, |
| ||||||||||
vibration, |
| Mower | blades are out of balance, | Replace | or balance blades, See Maintenance | ||||||||||
|
|
| |||||||||||||
|
|
|
|
|
|
|
| Section, |
|
|
|
|
| ||
|
|
| Belt installed incorrectly, | Reinstall | correctly, |
|
|
| |||||||
Mower drive | belt | Idler pulley spring broken or not properly | Repair or replace as needed. |
| |||||||||||
slips or fails | to | attached, |
|
|
|
|
|
|
|
|
|
| |||
drive. |
|
| Mower | drive belt broken, | Replace | drive belt, |
|
| |||||||
|
|
| PTO clutch | out of adjustment, | Adjust PTO clutch, | See Maintenance | Section, | ||||||||
38
