Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
|
| (when using 120 volts only) |
|
| |
Ampere | Rating | Totallength | ofcordinfeet |
| |
more qhan | not more th;_n | 25' | 50' | 100' | 150' |
0 | 6 | i18 | 16 | 16 | 14 |
6 | 10 | 18 | 16 | 14 | 12 |
10 | 12 | t6 | 16 | 14 | 12 |
12 | 16 | 14 | 12 | Notrecommended | |
SAVE THESE iNSTRUCTiONS
RECOMMENDED ACCESSORIES
Visit your Sears Hardware Department or see the Sears Power and Hand Tool Catalog to purchase recommended accessories for this power tool.
To avoid personal injury:
•Use only accessories recommended for this band saw. o Follow instructions that accompany accessories. Use of
improper accessories may cause hazards.
Use only accessories designed for this band saw to avoid injury from thrown broken parts or workpieces. Do not use any accessory unless you have completely read the instruction or owner'smanual for that accessory.
ITEM
Miter gauge
Blade width: 1/8", 1/4", 3/8",1/2"
Blade length: 80"
UNPACKING AND CHECKING
CONTENTS
Carefully unpack the band saw and all its parts, and compare against the list below and the illustration on page 7. Place the saw on a secure surface and examine it carefully.
oTo avoid injury from unexpected starting, do not plug the power cord into a power source receptacle during unpacking and assembly. This cord must remain unplugged whenever you are assembling or adjusting the saw.
o Although compact, this saw is heavy. To avoid back injury, get help whenever you have to lift the saw.
•If any part is missing or damaged, do not plug the band saw in until the missing or damaged part is replaced, and assembly is complete.
TABLE OF LOOSE PARTS
ITEM | DESCRIPTION | QUANTITY | ||
BAND | SAW |
|
|
|
A | Band | saw | with motor | 1 |
B. | Table | with | insert | 1 |
C. | Table | trunnions | 2 | |
D.Table hardware
| Hex bolts | 6 |
| Lock washers | 6 |
| Table alignment pin | 1 |
E. | Trunnion support bracket | ! |
F.Trunnion support hardware
|
| Long | bolt | 2 |
|
| Short hex. bolt | 1 | |
|
| Hex | nut | 1 |
|
| Table | lock knobs | 2 |
|
| Washers | 2 | |
G. | Miter | gauge | 1 | |
H. | Sawdust port | 1 | ||
|
| Hex | bolts | 2 |
|
| Washers | 2 | |
I. | Power | cord | hooks | 2 |
|
| Phillips head bolts | 2 | |
J. | Hex. key |
| 1 | |
K.Stand attachment hardware
|
| Large | washers | 8 |
|
| Hex. | nuts | 4 |
|
| Long | hex. bolts | 4 |
LEG STAND |
|
|
| 1 |
L. | Leg stand top plate | |||
M. | Legs |
|
| 4 |
|
| 2 | ||
N. | Short | lower | brackets | |
O. | Long | lower | brackets | 2 |
R | Foot pads |
| 4 | |
Q.Bag:
Carriage bolts | 32 |
Hex. nuls | 32 |
Washers | 32 |
|
UNPACKING YOUR BAND SAW
BCD
EFG
HIJ
| A |
|
|
|
|
|
|
| K |
| L |
I | oo | °o | 1 | F, | ,°! |
|
| ° | ° | ||
f °° | °° | 1 |
| N | |
I |
| °o | I |
|
|
I°° | °° | 1 |
|
| |
| M |
|
|
| O |
P
