SERVICE AND ADJUSTMENTS
O
o
o
o
Remove additional debris by back flushing water sup-
ply through wand (Fig, 30). Back flush between 30 to 60 seconds. Turn wand to stream spray and move nozzle from low to high while flushing.
Reinstall nozzle into the wand. DO NOT overtighten_
Reconnect the wand to the gun
Reconnect the water supply, tum on the water, and start the engine.
oTest the pressure washer by operating with nozzle in the high and in the low position.
FIG. 30
STORAGE
AFTER EACH USE
Water should not remain in the unit for long periods of time. Sediments of minerals can deposit on pump parts and "freeze" pump action. Follow these procedures after every
use:
oFlush detergent hose by placing the injector filter into a pail of clear water while running Pressure Washer' with nozzle in low pressure mode. Flush until you can see clear water running through the tube
=Shut off the engine and let it cool, then remove all hoses.
"STOP" POSITION BEFORE YOU CONTINUE. IF I
YOU START THE ENGINE WITHOUT THE PROPER
l_, CAUTION: BE SURE THE THROTTLE LEVER IS IN [
AGEWATERTHESUPPLYPuMPCONNECTEDj. YOU CAN DAM-
=Empty the pump of all pumped liquids by pulling recoil handle about 6 times_ This should remove most of the liquid in the pump,
oCoil the high pressure hose and inspect it for damage. Cuts in the hose or fraying of it could result in leaks and loss of pressure. Should any damage be found, replace the hose. DO NOT attempt to repair a damaged hose and use it. Replace the hose with the genuine Crafts- man part.
•Drain water from hose and properly hang it on the wire support provided on the guide handle.
NOTE; To protect the unit from freezing temperatures, you can draw windshield washer fluid into the pump by pouring the washer fluid into a
nected to the inlet adaptor and pulling the recoil handle twice.
,,Store in a clean, dry area.
LONG TERM STORAGE
,_ WARNING: NEVER STORE ENGINE WITH FUELIN TANK INDOORS OR IN ENCLOSED, POORLY VEN-
TILATED AREAS WHERE FUMES MAY REACH AN OPEN FLAMEp SPARK OR PILOT LIGHT AS ON A FURNACE, WATER HEATER, CLOTHES DRYER OR OTHER GAS APPLIANCE.
If you do not plan to use the Pressure Washer for more than 30 days, you must prepare the engine for long term storage.
NOTE: As always, prepare the pressure washer pump as
you would after each use.
It is important to prevent gum deposits from forming in essential fuel system parts such as the carburetor, fuel filter, fuel hose or tank during storage. Also, experience indicates that
To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Follow these instructions:
Protect Fuel System: Engines stored over 30 days need to be protected or drained of fuel to prevent gum deposits from forming in fuel system or on essential carburetor parts,
*For engine protection use a fuel stabilizer, Mix stabilizer with fuel in fuel tank and run engine for short time to circulate stabilizer through carburetor_
=If you did use "gasohol", run engine until engine stops from lack of fuel. Make sure you have water supply to pump inlet connected and turned ON,
Change Oil: While engine is still warm, drain oil from crankcase. Refill with recommended grade,
Oil Cylinder Bore: Remove spark plug and pour about 1/2 ounce (15mi) of engine oil into the cylinder, Cover spark plug hole with rag_ Crank slowly to distribute oilo
CAUTIONIHOLE WHENAVOIDCRANKINGSPRAYENGINEFROMSLOWLYSPARK . PL.UG I
,,Install spark plug. Do not connect spark plug wire.
OTHER
,,Do not store gasoline from one season to another.
,,Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.
=If possible, store your unit indoors and cover it to give pTrotectionfrom dust and dirt. BE SURE TO EMPTY
HE FUEL TANK.
,,Cover your unit with a suitable protective cover that does not retain moisture_
IMPORTANT: NEVER COVER YOUR PRESSURE WASHER WHILE ENGINE AND EXHAUST AREAS ARE
WARM
]8
