Craftsman 580.75231 Probmem, Correction, inlet is blocked, Pump has, loss, of pressure, is not

Models: 580.75231

1 48
Download 48 pages 38.39 Kb
Page 19
Image 19
Probmem

Probmem

 

 

 

 

Cause

 

 

 

 

 

 

 

Correction

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Nozzle

in low pressure mode.

 

1.

Pull nozzle backward for high

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

pressure

 

mode.

 

 

 

 

 

 

 

 

 

 

2.

Water

inlet is blocked.

 

 

2.

Clear inlet.

 

 

 

 

 

 

 

 

 

 

 

 

3.

Inadequate

water supply.

 

 

3.

Provide

adequate

water flow.

Pump has

following

 

4.

Inlet hose is kinked or leaking.

 

4.

Straighten

inlet hose,

patch leak.

problems:

failure

to

 

5.

Clogged inlet

hose strainer.

 

5.

Check and clean

inlet

hose strainer.

produce

pressure,

erratic

 

pressure,

chattering,

loss

6.

Water

supply

is over

100°F.

 

6.

Provide

cooler

water supply.

of pressure,

low water

7.

High pressure

hose

is blocked

or

7.

Clear blocks

in outlet

hose.

volume.

 

 

 

 

 

 

 

 

 

 

 

leaks.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8.

Gun

leaks.

 

 

 

 

 

8.

Replace

gun.

 

 

 

 

 

 

 

 

 

 

 

9.

Nozzle

is obstructed.

 

 

 

9.

Clean nozzle.

 

 

 

 

 

 

 

 

 

 

 

10.

Pump

is faulty.

 

 

 

10.

Contact

Sears

service

facility.

 

 

 

 

 

 

 

1.

Detergent siphoning

tube

is not

 

1.

Insert detergent siphoning

tube into

 

 

 

 

 

 

 

 

submerged.

 

 

 

 

 

 

detergent.

 

 

 

 

 

 

Detergent fails to mix with

2.

Chemical filter

is clogged.

 

 

2.

Clean or replace

filter/detergent

 

 

 

 

 

 

 

 

 

 

siphoning

tube.

 

 

 

spray.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Dirty

in=linefilter.

 

 

 

3.

See

"Check

In=Line filter".

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Nozzle

is in high pressure

mode.

4.

Push nozzle

forward for low

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

pressure

 

mode.

 

 

 

Engine tuns good at no-

Engine speed is too slow.

 

 

Move throttle

control

to FAST

position. If

load

but "bogs"

when load

 

 

 

 

 

 

 

 

 

engine still "bogs down", contact Sears

is added.

 

 

 

 

 

 

 

 

 

 

 

 

 

service

facility.

 

 

 

 

 

 

 

 

 

 

 

 

1.

Low

oil level.

 

 

 

 

1.

Fill

crankcase

to

proper level.

 

 

 

 

 

 

 

2.

Dirty

air cleaner.

 

 

 

2.

Clean or replace

air cleaner.

 

 

 

 

 

 

 

3.

Out of gasoline.

 

 

 

3.

Fill fuel

tank.

 

 

 

 

 

 

 

 

 

 

 

 

4.

Stale

gasoline.

 

 

 

 

4.

Drain gas tank; fill with fresh fuel.

Engine witl not start; or

5.

Spark

plug wire not connected

to

5.

Connect

wire

to spark

plug.

starts

and

tuns
tough.

 

spark

plug.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.

Bad spark

plug.

 

 

 

6.

Replace

spark

plug.

 

 

 

 

 

 

 

 

 

7.

Water

in gasoline.

 

 

 

7.

Drain gas tank; fill with fresh fuel.

 

 

 

 

 

 

 

8.

Overchoking.

 

 

 

 

8.

Open choke fully and crank engine.

 

 

 

 

 

 

 

9.

Excessively

rich fuel

mixture.

 

9.

Contact

Sears

service

facility.

Engine

shuts

down

during

1.

Out of gasoline.

 

 

 

1.

Fill fuel

tank.

 

 

 

 

 

operation.

 

 

 

 

2.

Low

oil level.

 

 

 

 

2.

Fill

crankcase

to

proper level.

Engine

lacks

power.

Dirty air filter.

 

 

 

 

 

Replace

air

filter.

 

 

 

 

 

Engine

"hunts"

or falters.

Choke is opened too soon.

 

 

Move choke to halfway position until

 

 

 

 

 

 

 

 

 

engine runs smoothly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

Page 19
Image 19
Craftsman 580.75231 Probmem, Correction, inlet is blocked, Pump has, loss, of pressure, is not, in=linefilter, tuns, tough