TROUBLESHOOTING

 

CHART

 

 

 

 

 

 

 

 

 

 

 

 

 

PROBLEM

 

CAUSE

 

 

 

 

 

 

CORRECTION

 

 

 

 

 

Engine clicks but

Weak

 

or dead

battery.

Recharge

or replace

battery.

will not start

Corroded

battery

termi-

Clean

battery

terminals.

 

 

 

 

nals.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Loose

or damaged

wiring.

 

Check all wiring.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Check/replace solenoid or

 

 

Faulty

solenoid or starter.

 

starter.

 

 

 

 

 

 

Loss of power

Cutting

too much

 

 

 

Set in "Higher

Cut" posi-

 

 

 

grass/too

fast.

 

 

 

 

tion/reduce

speed.

 

 

 

 

Throttle in =CHOKE"

posi-

 

Adjust

throttle

control.

 

 

 

 

tion.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Build-up of grass, leaves

 

Clean

underside of mower

 

 

 

and trash

under

mower.

 

housing.

 

 

 

 

 

 

 

 

Dirty

air filter.

 

 

 

 

Clean/replace

air filter.

 

 

 

Low

oil level/dirty

oil.

 

Check

oil level/change

oil.

 

 

Faulty

spark plug.

 

 

Clean

and regap

or change

 

 

 

 

 

 

 

 

 

 

 

spark plug.

 

 

 

 

 

 

Dirty

fuel filter.

 

 

 

 

Replace

fuel filter.

 

 

 

 

Stale

or dirty fuel.

 

 

Drain fuel tank and refill with

 

 

Water

in fuel.

 

 

 

 

fresh

gasoline.

 

 

 

 

 

 

 

 

 

Drain fuel tank and carbure-

 

 

 

 

 

 

 

 

 

 

 

tor, refill tank with fresh gaso-

 

 

 

 

 

 

 

 

 

 

 

line and

replace fuel

filter.

 

 

Spark

plug wire loose.

 

Connect

and tighten

spark

 

 

 

 

 

 

 

 

 

 

 

plug wire.

 

 

 

 

 

 

 

Dirty engine air

 

 

 

Clean

engine

air screen/fins.

 

 

 

screen/fins.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Dirty/clogged

muffler.

 

Clean/replace

muffler.

 

 

 

Loose

or damaged

wiring.

 

Check

all wiring.

 

 

 

 

 

Carburetor

out of adjust-

 

See "To Adjust Carburetor" in

 

 

 

ment.

 

 

 

 

 

 

Service

and Adjustments

 

 

 

 

 

 

 

 

 

 

 

section.

 

 

 

 

 

 

 

 

Engine valves

out of

 

Contact

an authorized

ser-

 

 

 

adjustment.

 

 

 

 

vice center.

 

 

 

 

Excessive

vibration

Worn, bent or loose blade.

Replace blade. Tighten blade

 

 

 

 

 

 

 

 

 

 

 

bolt.

 

 

 

 

 

 

 

 

 

Bent

blade mandrel.

 

Replace

blade mandrel.

 

 

Loose/damaged

part(s).

Tighten

loose

pad(s).

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace

damaged

parts.

Engine continues to

Faulty

operator-safety

 

Check

wiring,

switches

and

run when operator

 

presence

control

system.

 

connections.

If not

 

 

leaves seat with

 

 

 

 

 

 

 

 

 

corrected,

contact

an autho-

attachment

clutch

 

 

 

 

 

 

 

 

 

rized

service

center/

 

 

engaged

 

 

 

 

 

 

 

 

 

 

department.

 

 

 

 

30

Page 30
Image 30
Craftsman 917.27108 owner manual Engine clicks but, Will not start, Check all wiring Check/replace solenoid or, Starter