Craftsman 917.27623 Faulty operator-safety, Troubleshootingchart, Problem, Cause, Correction

Models: 917.27623

1 60
Download 60 pages 45.32 Kb
Page 31
Image 31
TROUBLESHOOTINGCHART:

TROUBLESHOOTINGCHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM

CAUSE

 

 

 

 

 

 

 

 

CORRECTION

 

 

 

 

 

Loss of power

1.

Cutting

too

much

grass/too

1.

Raise

cutting

height/reduce

 

 

fast.

 

 

 

 

 

 

 

 

 

speed.

 

 

 

 

 

 

 

 

2.

Throttle

 

in "CHOKE"

position.

2.

Adjust

throttle

control.

 

 

3.

Build-up

 

of grass,

leaves

3.

Clean

underside

 

of

mower

 

 

and

trash

under

mower,

 

housing.

 

 

 

 

 

 

 

 

4.

Dirty

air

filter.

 

 

 

 

4.

Clean/replace

 

air

filter.

 

 

5.

Low

oil

level/dirty

oil.

 

5.

Check

oil

level/change

oil.

 

6.

Faulty

spark

plug.

 

 

6.

Clean

and

regap

or

change

 

 

 

 

 

 

 

 

 

 

 

 

spark

plug.

 

 

 

 

 

 

7.

Dirty

fuel

filter.

 

 

 

7.

Replace

fuel

filter.

 

 

 

8.

Stale

or

dirty

fuel.

 

 

8.

Empty fuel tank and refill tank

 

 

 

 

 

 

 

 

 

 

 

 

with fresh,

clean

gasoline.

 

9.

Water

in

fuel.

 

 

 

 

9.

Empty

fuel

tank

and

car

 

 

 

 

 

 

 

 

 

 

 

 

buretor, refill tank with fresh

 

 

 

 

 

 

 

 

 

 

 

 

gasoline

and

replace

fuel

 

 

 

 

 

 

 

 

 

 

 

 

filter.

 

 

 

 

 

 

 

 

 

10.

Spark

plug

wire

loose.

10.

Connect

and

tighten

spark

 

 

 

 

 

 

 

 

 

 

 

 

plug

wire.

 

 

 

 

 

 

 

11.

Dirty

engine

air

screen/fins.

11.

Clean

engine

air

screen/

 

 

 

 

 

 

 

 

 

 

 

 

 

fins.

 

 

 

 

 

 

 

 

 

12.

Dirty/clogged

 

muffler.

 

12.

Clean/replace

 

muffler.

 

 

13.

Loose

or

damaged

wiring.

13.

Check

all wiring.

 

 

 

 

14.

Carburetor

out

of

adjustment.

14.

See "To Adjust

Carburetor"

 

 

 

 

 

 

 

 

 

 

 

 

in Service

and

Adjustments

 

 

 

 

 

 

 

 

 

 

 

 

section.

 

 

 

 

 

 

 

 

15.

Engine

valves

out

of

 

15.

Contact

a

Sears

or

other

 

 

adjustment,

 

 

 

 

 

 

qualified

service

 

center.

 

Excessive

1.

Worn,

bent

or

loose

blade.

1.

Replace

blade.

 

 

 

 

vibration

 

 

 

 

 

 

 

 

 

 

 

Tighten

blade

bolt.

 

 

 

2.

Bent

blade

mandrel.

 

2.

Contact

a

Sears

or

other

 

 

 

 

 

 

 

 

 

 

 

 

qualified

service

 

center.

 

 

3.

Loose/damaged

 

part(s).

.

Tighten

loose

part(s).

 

 

 

 

 

 

 

 

 

 

 

 

 

Replace

damaged

parts.

Engine dies when . Reverse operation system

tractor is shifted(ROS) is not "ON" while

into reversemower or other attachment is engaged.

1.Turn ignition key to ROS "ON" position. See Operation section.

Engine continues

1. Faulty operator-safety

1. Check

wiring,

switches

and

to run when

presence control system.

connections.

If not corrected,

operator

leaves

 

contact

Sears

or

other

 

seat

with

attach-

 

qualified

service

center.

 

ment

clutch

 

 

 

 

 

 

engaged

Poor cut - uneven . Worn, bent or loose blade.

2.Mower deck not level.

3.Buildup of grass, leaves, and trash under mower.

4.Bent blade mandrel.

5.Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels.

1.Replace blade. Tighten blade bolt.

2.Level mower deck.

3.Clean underside of mower housing.

4.Contact a Sears or other qualified service center.

5.Clean around mandrels to open vent holes.

31

Page 31
Image 31
Craftsman 917.27623 Faulty operator-safety, Troubleshootingchart, Problem, Cause, Correction, Loss of power, to run when