TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be nec- essary, check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move choke control (located on dash panel) to full choke position.

2.Remove air cleaner cover, filter and cartridge plate to expose carburetor choke (See "AIR FILTER" in the Main- tenance section of this manual).

3.Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw

securely.

4.Reassemble air cleaner.

Closed For Full Choke _......

I "

!!l!!ii!t i:,

,'J'l[i ,il[z

TO ADJUST CARBURETOR

The carburetor has been present at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture. Turning the adjusting needles out

(counterclockwise) increases the supply

of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: Damage to the needles and the seats in carburetor may result if screw is turned in too tight.

PRELIMINARY SETTING -

1.Be sure you have a clean air fil- ter, and the throttle control cable is

adjusted properly (see "TO ADJUST THROTTLE CONTROL CABLE" in the

Service and Adjustments section of this manual).

. With engine off turn idle fuel adjust- ing needle in (clockwise) closing it finger tight and then turn out (counter- clockwise) 1 turn.

FINAL SETTING -

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

NOTE: The high idle is set at the factory and cannot be adjusted.

2.Idle speed setting - With throttle control lever in slow position, engine should idle at 1750 RPM. If engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is at- tained.

3.Idle fuel needle setting - With throttle control lever in slow position, turn idle fuel adjusting needle in (clockwise) until engine speed decreases and then

turn out (counterclockwise) approxi- mately 3/4 turn to obtain the best low speed performance.

4.Recheck idle speed. Readjust if neces- sary.

ACCELERATION TEST -

5.Move throttle control lever from slow

to fast position. If engine hesitates or dies, turn idle fuel adjusting needle out

(counterclockwise) 1/8 turn. Repeat test and continue to adjust, if necessary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not

adjust-damage may result.

IMPORTANT: Never tamper with the engine governor, which is factory set for

proper engine speed. Overspeeding the engine above the factory high speed set- ting can be dangerous. If you think the en-

gine-governed high speed needs adjusting, contact a Sears or other qualified service center, which has proper equipment and experience to make any necessary adjust- ments.

28

Page 27 Page 29
Page 28
Image 28
Craftsman 917.27623 To Adjust Choke Control, To Adjust Carburetor, Preliminary Setting, Final Setting, Acceleration Test
Page 27 Page 29

917.27623 specifications

The Craftsman 917.27623 is a versatile and robust lawn tractor designed to make lawn maintenance efficient and enjoyable. With its user-friendly features and advanced technologies, this machine enhances the mowing experience for homeowners and lawn care enthusiasts alike.

One of the standout features of the Craftsman 917.27623 is its powerful 24-horsepower Briggs & Stratton engine. This reliable engine provides ample power, facilitating smooth operation even during challenging mowing conditions. The engine is paired with a smooth hydrostatic transmission, which allows for effortless speed adjustments and greater control, making it easy to navigate around tight corners and obstacles in the yard.

The mower is equipped with a generous 46-inch cutting deck. This size strikes an ideal balance between maneuverability and cutting efficiency, allowing users to tackle medium to large yards in less time. The deck also features a three-blade system, ensuring that grass is cut evenly and cleanly, promoting overall lawn health. Moreover, the cutting height can be easily adjusted with a simple lever, offering users the flexibility to maintain their lawns at different heights based on personal preference and seasonal needs.

In terms of durability, the Craftsman 917.27623 boasts a robust steel frame that can withstand the rigors of regular lawn maintenance. The materials used in its construction are designed to resist rust and corrosion, enhancing the lifespan of the mower.

Ergonomics play a key role in the design of the Craftsman 917.27623. The tractor features a comfortable high-back seat that reduces fatigue during extended use. Additionally, the dual-lever steering provides enhanced maneuverability, making it easy to steer the mower in tight spaces or around landscaping features.

Another significant technology integrated into this mower is its mulching capability. By utilizing the optional mulching kit, users can finely chop grass clippings, allowing them to decompose and return nutrients to the lawn. This promotes a healthier lawn and reduces the need for additional fertilization.

Overall, the Craftsman 917.27623 stands out for its powerful performance, user-friendly features, and durability. With its optimal cutting system and thoughtful design, it serves as an excellent addition to any homeowner's lawn care arsenal, transforming the often mundane chore of mowing into a more pleasant and efficient task.
Top Page Image Contents