Manuals / Brands / Computer Equipment / Computer Hardware / Creative / Computer Equipment / Computer Hardware

Creative AWE64 Changing your E-MailAddress, Sound Cards and your Creative WebPhone, Audio Programs and your Creative WebPhone

1 89

Download 89 pages, 833.84 Kb

Changing your E-Mail Address

In the event you change your e-mail address (e.g., you change your Internet service provider), you will need to change your E-Mail address in the Network Parameters section of the Creative WebPhone Configure window. A message will be displayed when your e-mail address change has been confirmed.

Audio Programs and your Creative WebPhone

Playing audio (WAV, MIDI, CD player...) through your sound card with another program while Creative WebPhone is running is not a good idea and may prevent Creative WebPhone from operating properly. When Creative WebPhone requires control of the sound card (to play a sound effect or to allow conversation with a party) and the sound card is in use, it will attempt to terminate the sound being played. If Creative WebPhone cannot gain control of the sound card, it will display a dialog box informing you “Sound Card Already In Use”. If this occurs during an active conversation, the call will be placed on hold. Correct the problem (stop using the sound card with the other application) and take the call off hold to resume your conversation.

Sound Cards and your Creative WebPhone

Make sure your Voice Activation Level (located in the Creative WebPhone flip door), is set to recognize silence. Otherwise, the parties you call using half duplex sound cards will never get an opportunity to talk (they will always see LISTEN in their display and you will always see TALK in your display). If this happens, stop talking into the microphone and move the Voice Activation Level (VOX) slider to the right until the VOX meter displays Silence and you see the red bar. Now verify the VOX enunciator displays Speaking and the red bar disappears (covered by the green bar) only when you talk into the microphone.

You will obtain superior audio performance if you enable your sound card’s automatic gain control (AGC) via the mixer application bundled with your sound card.

14

Contents

Getting Started Quick Start for INTERNETed Audio Tools Plug and Play Install Tips Notes for WaveSynth/WG Users Getting Started Page Contents Appendices AGeneral Specifications BUnderstanding the Installation B-1 B-2 Page ❑Checking System Requirements ❑Using This Guide ❑Getting More Information ❑Document Conventions Checking System Requirements Getting More Information Document Conventions Text Conventions Text Element Use Icons Icon Setting Up Your Audio Card User’s Guide 1.Start CreativeWaveSynth-Waveguide The WaveSynth/WG properties sheet appears, displaying the Profile tab 2.Click the Performance Settings button 4.In the WaveSynth/WG properties sheet, click the Quit button to close it To install the card and related peripherals: 3.Remove your system’s cover Find a free Page Page Installing Software in Windows If a dialog box similar to \WIN95\DRIVERS Page The Media Player appears as shown in Figure 2.On the Device menu, click Sound 4.On the Media Player, click Page Installing Software in DOS/ Windows C:\SB16 DIAGNOSE Using Memory Managers Bypassing the Loading of the Low-LevelDrivers Page General Specifications Built-inDigital/Analog Mixer Volume Control 3D Stereo Enhancement Technology MIDI Interface Upgrade Options Understanding the Installation SET Input/Output (I/O) Addresses I/O Address Range Device Interrupt Request (IRQ) Lines IRQ Line Direct Memory Access (DMA) Channels DMA Channel Usage SOUND Environment Variable BLASTER Environment Variable Parameter Description MIDI Environment Variable The AUTOEXEC.BAT File Settings The CONFIG.SYS File Settings DIAGNOSE /A Page Changing Audio Card Settings In MS-DOS/Windows3.1x CT3DSE ON CT3DSE OFF [sndblst.drv] FullDuplex=1 FullDuplex=0 Page Page To enable it, select the check box 7.Click the OK button and restart Windows 95 for the change to take effect To enable or disable the interface in MS-DOS: 1.Exit to MS-DOSif you are in Windows CTCU Troubleshooting Causes Problem SOUND or BLASTER environment could not be found Problem Error message “Out of environment space” Cause The system environment space is used up Add the statement SYSEDIT Page Resolving Conflicts in Windows Resolving Conflicts in MS-DOS/Windows3.1x Technical Support Page FaxBack +353 1 Quick Start Interneted Audio Setting Up Microsoft Internet Explorer Setting Up the Dialing and Service Provider Information Page To Set Up a Dial-UpScript Running Microsoft Internet Explorer Setting up Microsoft Internet Explorer Page Page Connecting to Your Internet Service Provider Entering your activation key Entering information in the Configure window Entering your User Information Information Entering your Network Parameters WebPhone Password Network Parameter descriptions Changing your E-MailAddress Audio Programs and your Creative WebPhone Sound Cards and your Creative WebPhone Modems and your Creative WebPhone Bandwidth and your Answering Machine Troubleshooting Page Page Page 4.Type D:\ENGLISH\WIN31\CTCM\INSTALL CTCM ❑Your PnP cards’ settings do not work properly ❑You need to add resource settings for new and existing legacy (non-PnP)cards ❑You have changed the resource settings of your legacy cards ❑You have removed a legacy card from your system To run CTCU in DOS/Windows 3.1x: The CTCU Interface PnP Cards Section Reconfigure Button ❑I/O Range window ❑Interrupt window ❑Direct Memory Access window ❑Memory Range window Legacy Cards Section Page System Devices Section PCI Devices Section Generally, a PnP card requires one of the following to work: ❑PnP System BIOS ❑PnP Operating System ❑PnP Configuration Drivers and Utilities PnP System BIOS PnP Operating System PnP Configuration Drivers and Utilities Page Why Use CTCM and CTCU Limitations of CTCM and CTCU General Questions ICM (or other Configuration Manager) Questions CTCU Question CTCM Questions Page Page Notes for WaveSynth/WG Users