Creative AWE64 Why Use CTCM and CTCU, Limitations of CTCM and CTCU

Why Use CTCM and CTCU?

There are several reasons why we offer CTCM and CTCU:

1.CTCM provides a consistent method for configuring all Creative PnP cards. It works with or without PnP BIOS or ICM. If your PnP BIOS or ICM has already configured your PnP card(s), CTCM will simply retain those settings.

2.If the PnP BIOS or ICM did not configure your Creative PnP cards properly, due to incompatibility problems similar to those mentioned in the section “ PnP in DOS/Windows 3.1x” in page 14, CTCM may be able to allocate resources to these cards.

3.You need not reboot your system after using CTCU to change Creative PnP card settings, if you do not have any DOS device drivers (e.g., SBIDE.SYS or CTSB16.SYS) loaded. You only need to run CTCM to reconfigure the card. This is possible because CTCM can be activated from the DOS prompt, unlike ICM.

Limitations of CTCM and CTCU

If you use a non-PnP operating system like DOS/Windows 3.1x and do not have a PnP BIOS or ICM, your PnP card works like a software-configurable card.

In such an environment, CTCM needs to know which resources have been reserved by all the legacy and PnP cards, and system devices in your system before it can allocate conflict-free resources to your new Creative PnP card.

CTCM can get the resource settings of PnP cards and system devices from the PnP cards and BIOS. But you need to use CTCU to enter the resource settings of all the legacy cards in your PC, and then run CTCM to configure your Creative PnP card.

You may still encounter hardware conflicts if the resource settings specified through CTCU are incomplete or wrong. If this happens, use CTCU to select a different group of resources for the Creative PnP card that caused the conflict. You may need to try a few combinations until you find one that works. This can be tedious, but it is easier than the legacy way of changing dip switches or jumpers.

16

Contents

Getting Started Quick Start for INTERNETed Audio Tools Plug and Play Install Tips Notes for WaveSynth/WG Users Getting Started Page Contents Appendices AGeneral Specifications BUnderstanding the Installation B-1 B-2 Page ❑Checking System Requirements ❑Using This Guide ❑Getting More Information ❑Document Conventions Checking System Requirements Getting More Information Document Conventions Text Conventions Text Element Use Icons Icon Setting Up Your Audio Card User’s Guide 1.Start CreativeWaveSynth-Waveguide The WaveSynth/WG properties sheet appears, displaying the Profile tab 2.Click the Performance Settings button 4.In the WaveSynth/WG properties sheet, click the Quit button to close it To install the card and related peripherals: 3.Remove your system’s cover Find a free Page Page Installing Software in Windows If a dialog box similar to \WIN95\DRIVERS Page The Media Player appears as shown in Figure 2.On the Device menu, click Sound 4.On the Media Player, click Page Installing Software in DOS/ Windows C:\SB16 DIAGNOSE Using Memory Managers Bypassing the Loading of the Low-LevelDrivers Page General Specifications Built-inDigital/Analog Mixer Volume Control 3D Stereo Enhancement Technology MIDI Interface Upgrade Options Understanding the Installation SET Input/Output (I/O) Addresses I/O Address Range Device Interrupt Request (IRQ) Lines IRQ Line Direct Memory Access (DMA) Channels DMA Channel Usage SOUND Environment Variable BLASTER Environment Variable Parameter Description MIDI Environment Variable The AUTOEXEC.BAT File Settings The CONFIG.SYS File Settings DIAGNOSE /A Page Changing Audio Card Settings In MS-DOS/Windows3.1x CT3DSE ON CT3DSE OFF [sndblst.drv] FullDuplex=1 FullDuplex=0 Page Page To enable it, select the check box 7.Click the OK button and restart Windows 95 for the change to take effect To enable or disable the interface in MS-DOS: 1.Exit to MS-DOSif you are in Windows CTCU Troubleshooting Causes Problem SOUND or BLASTER environment could not be found Problem Error message “Out of environment space” Cause The system environment space is used up Add the statement SYSEDIT Page Resolving Conflicts in Windows Resolving Conflicts in MS-DOS/Windows3.1x Technical Support Page FaxBack +353 1 Quick Start Interneted Audio Setting Up Microsoft Internet Explorer Setting Up the Dialing and Service Provider Information Page To Set Up a Dial-UpScript Running Microsoft Internet Explorer Setting up Microsoft Internet Explorer Page Page Connecting to Your Internet Service Provider Entering your activation key Entering information in the Configure window Entering your User Information Information Entering your Network Parameters WebPhone Password Network Parameter descriptions Changing your E-MailAddress Audio Programs and your Creative WebPhone Sound Cards and your Creative WebPhone Modems and your Creative WebPhone Bandwidth and your Answering Machine Troubleshooting Page Page Page 4.Type D:\ENGLISH\WIN31\CTCM\INSTALL CTCM ❑Your PnP cards’ settings do not work properly ❑You need to add resource settings for new and existing legacy (non-PnP)cards ❑You have changed the resource settings of your legacy cards ❑You have removed a legacy card from your system To run CTCU in DOS/Windows 3.1x: The CTCU Interface PnP Cards Section Reconfigure Button ❑I/O Range window ❑Interrupt window ❑Direct Memory Access window ❑Memory Range window Legacy Cards Section Page System Devices Section PCI Devices Section Generally, a PnP card requires one of the following to work: ❑PnP System BIOS ❑PnP Operating System ❑PnP Configuration Drivers and Utilities PnP System BIOS PnP Operating System PnP Configuration Drivers and Utilities Page Why Use CTCM and CTCU Limitations of CTCM and CTCU General Questions ICM (or other Configuration Manager) Questions CTCU Question CTCM Questions Page Page Notes for WaveSynth/WG Users