LUBRICATION GUIDE

(International Cub Cadet 71, 102 and 122 Tractors)

--After Every 10 Hours of Operation

1 -Oi I fi lief ca p and bayanet-type oil level gauge.

2- Steering knuckles (2).

3- Front oxle pivot pin.

-Engine crankcase.

5- Power take-off shaft bearing

Transmission

6 -Oil level and filler plug.

7 -Oil drain plug.

Creeper drive housing

8.Levelplug.

9.Breatherandfiller plug.

10.Drainplug.

11 -Steering gear housing.

Miscellaneous

Check the oil (with the engine stopped) and add sufficient

new oil to bring it to the "FULL" mark on the gauge. Do

not overfill. Do not operate the engine if the oil level is below the "LOW" mark on the gauge.

Use 1H-251 HEP grease or equivalent #2 multi-purpose

lithium grease and apply sufficient grease to flush out oldgrease and dirt.

--After Every 30 Hours of Operation

While the oil is warm, remove the drain plug (4) and drain

all of the oil from the crankcase. Replace the drain plug.Remove the crankcase oil filler cap (1). Refill the crank-

case with new oil up to the "FULL" mark on the oil levelgauge.

Refer to the "Lubrication Table" for the proper quantity and viscosity to use.

--After Every 100 Hours of Operation

Use IH-2.5l HEP grease or equivalent #2. multi-purpose

{ lithium grease and apply two or three strokes of the lubri-

cator to the lubrication fittings.

--Periodic

Check the oil level periodically. Keep the lubricant up tothe level plug (6) on the rear of the transmission case.

Change the oil in the transmission case at least once a year. Remove the drain plug (7) and remove the oil level and filler plug (6) and allow all of the oil to drain out. Re- place the drain plug. Refill with approved lubricant up to the level plug opening and replace the plug.

Check the oil level periodically. Keep the lubricant up to the level plug (8) on the left side of the creeper drive housing. Drain and refill the housing each time the oil is

changed in the transmission case. To change the oil, re- move the drain plug (I 0) at the bottom of the housing and allow all the oil to drain. Then replace the drain plug.

Remove the breather and oil filler plug (9) at the right of the creeper shift handle on top of the frame assembly, and remove the oil level plug (8). Fill to the level plug opening with approved lubricant and replace the plugs.

Once a year, apply two strokes of the lubricator, using

IH-251 HEP grease or equivalent #2 multi-purpose lithium grease.

Note/: To locate the lubrication fitting, turn the front

wheels to the maximum right turn position: Then reach up under the right side of the tractor frame to locate the

fitting.

Lubricate the clutch pedal shaft and linkage with eight or ten drops of engine oil.

29

Page 30 Page 32
Page 31
Image 31
Cub Cadet 71 manual Lubrication Guide, Breatherandfiller plug Drainplug
Page 30 Page 32

71 specifications

The Cub Cadet 71 is a classic garden tractor that has earned a place in the hearts of gardening enthusiasts and landscapers since its introduction in the 1970s. Renowned for its robust design and exceptional performance, the Cub Cadet 71 embodies reliability and efficiency in outdoor tasks.

At the heart of the Cub Cadet 71 is its powerful Kohler K161 engine, a proud testament to American engineering. This 7-horsepower engine provides ample power for mowing, tilling, and a variety of other gardening tasks. Its air-cooled, single-cylinder design ensures longevity and ease of maintenance, allowing users to focus on their gardening rather than frequent repairs.

One of the standout features of the Cub Cadet 71 is its cutting deck. With a 38-inch width, it effectively maneuvers through tight spaces while still providing a wide enough cutting path for larger areas. The deck is designed for a clean cut, featuring durable stamped steel construction that enhances its longevity. The height adjustment lever allows users to customize cutting heights according to their grass type and seasonal growth, ensuring optimal results.

The innovative gear drive transmission is another highlight of the Cub Cadet 71. This system provides seamless shifting between gears, allowing for better control when navigating slopes or tackling uneven terrain. The tractor also features a comfortable operator's platform with ergonomic controls, making it easy to operate for extended periods.

For enthusiasts looking to expand the capabilities of their Cub Cadet 71, various attachments are available. From snow throwers to front-end loaders, these accessories enhance the tractor’s functionality year-round, making it a versatile tool in any homeowner’s arsenal.

Safety is a key consideration in the design of the Cub Cadet 71. The tractor features a sturdy frame and low center of gravity, providing stability while on slopes. Additionally, the easy-to-use pedal system ensures that operators can maintain full control, reducing the risk of accidents.

In conclusion, the Cub Cadet 71 is not just a garden tractor; it’s a reliable partner for anyone passionate about maintaining their yard. With its powerful engine, versatile features, and robust design, it remains a beloved choice for those looking to enhance their gardening experience. Whether you’re a weekend warrior or a seasoned expert, the Cub Cadet 71 is sure to meet your demands with uncompromising performance.
Top Page Image Contents