5.Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

6.Do not operate machine while under the influence of alcohol or drugs.

7.Muffler and engine become hot and can cause a burn. Do not touch.

8.Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic.

9.Exercise caution when changing direction and while operating on slopes.

10.Plan your snow-throwing pattern to avoid discharge towards windows, walls, cars etc. Thus, avoiding possible property damage or personal injury caused by a ricochet.

11.Never direct discharge at children, bystanders and pets or allow anyone in front of the machine.

12.Do not overload machine capacity by attempting to clear snow at too fast of a rate.

13.Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run.

14.Disengage power to the auger/impeller when transporting or not in use.

15.Never operate machine at high transport speeds on slippery surfaces. Look down and behind and use care when backing up.

16.If the machine should start to vibrate abnormally, stop the engine, disconnect the spark plug wire and ground it against the engine. Inspect thoroughly for damage. Repair any damage before starting and operating.

17.Disengage all control levers and stop engine before you leave the operating position (behind the handles). Wait until the auger/impeller comes to a complete stop before unclogging the chute assembly, making any adjustments, or inspections.

18.Never put your hand in the discharge or collector openings. Always use the clean-out tool provided to unclog the discharge opening. Do not unclog chute assembly while engine is running. Shut off engine and remain behind handles until all moving parts have stopped before unclogging.

19.Use only attachments and accessories approved by the manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20.If situations occur which are not covered in this manual, use care and good judgment. Contact the dealer you purchased the unit from or call 1-877-282-8684 for the name of your nearest Cub Cadet service dealer.

Maintenance & Storage

1.Never tamper with safety devices. Check their proper operation regularly. Refer to the maintenance and adjustment sections of this manual.

2.Before cleaning, repairing, or inspecting machine disengage all control levers and stop the engine. Wait until the auger/impeller come to a complete stop. Disconnect the spark plug wire and ground against the engine to prevent unintended starting.

3.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage.

4.Do not change the engine governor setting or over-speed the engine. The governor controls the maximum safe operating speed of the engine.

5.Snow thrower shave plates and skid shoes are subject to wear and damage. For your safety protection, frequently check all components and replace with original equipment manufacturer’s (OEM) parts only. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!”

6.Check controls periodically to verify they engage and disengage properly and adjust, if necessary. Refer to the adjustment section in this operator’s manual for instructions.

7.Maintain or replace safety and instruction labels, as necessary.

8.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

9.Prior to storing, run machine a few minutes to clear snow from machine and prevent freeze up of auger/impeller.

10.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer etc.

11.Always refer to the operator’s manual for proper instructions on off-season storage.

Your Responsibility

Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

Do not modify engine

To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting of engine governor.

Notice regarding Emissions

Engines which are certified to comply with California and federal EPA emission regulations for SORE (Small Off Road Equipment) are certified to operate on regular unleaded gasoline, and may include the following emission control systems: Engine Modification (EM) and Three Way Catalyst (TWC) if so equipped.

DANGER

NEVER PUT HAND IN CHUTE. CONTACT WITH ROTATING PARTS CAN AMPUTATE FINGERS AND HANDS.

SHUT OFF ENGINE AND WAIT UNTIL ALL MOVING PARTS HAVE STOPPED BEFORE UNCLOGGING.

USE CLEAN-OUT TOOL OR WOODEN STICK TO UNCLOG CHUTE.

4

Page 3 Page 5
Page 4
Image 4
Cub Cadet 730 STE manual Your Responsibility, Maintenance & Storage, Do not modify engine
Page 3 Page 5

730 STE specifications

The Cub Cadet 730 STE is a powerful and versatile snow blower designed to tackle even the toughest winter conditions. Featuring a robust 24-inch clearing width, this snow thrower is engineered to handle heavy snowfall with ease. Its impressive throwing distance, which can reach up to 40 feet, makes it an ideal choice for both residential and commercial use. The 730 STE is equipped with a strong 277cc engine that provides reliable performance and the necessary power to push through packed snow and ice.

One of the standout features of the Cub Cadet 730 STE is its innovative track drive system. This advanced system ensures superior traction and stability on various surfaces, including steep inclines and uneven terrain. The track drive design gives users added confidence, allowing them to navigate snowy pathways and driveways without slipping or losing control.

The snow blower also incorporates a user-friendly control panel, allowing operators to easily manage speed settings and directional control. With multiple speed settings, the 730 STE enables users to adjust the pace for optimal efficiency based on the depth and type of snow being cleared. The highly maneuverable design of the snow blower makes it easy to work around obstacles such as mailboxes, fences, and landscaping.

Another remarkable feature of the Cub Cadet 730 STE is its adjustable chute. The 180-degree rotating chute allows users to direct the snow wherever they wish, ensuring efficient removal without worrying about blowing snow back onto already cleared areas. The chute is made from durable materials, enhancing its lifespan while maintaining effective performance.

Safety is also a priority in the design of the 730 STE. The snow blower comes with features such as a headlight for improved visibility during early morning or late evening snow clearing, making it safer to operate under low light conditions. Additionally, the durable and reinforced construction guarantees longevity and reliability throughout many winter seasons.

In summary, the Cub Cadet 730 STE stands out in the snow blower market with its powerful engine, superior traction, adjustable chute, and user-friendly controls. These characteristics make it an exceptional choice for anyone looking to tackle winter weather efficiently and effectively. Whether you're clearing your driveway or maintaining a commercial lot, the 730 STE is equipped to handle the task with performance and precision.
Top Page Image Contents