CyberPower Systems PP1500E, PP2200E user manual Battery Replacement and Storage, Trouble Shooting

BATTERY REPLACEMENT AND STORAGE

Contact your dealer or call the number in this manual for information on battery replacement.

Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the supervision of personnel knowledgeable of batteries and their precautions. Keep unauthorized personnel away from batteries.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries. CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as it may explode. Follow all local ordinances regarding proper disposal of batteries.

CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electric shock. Take the following precautions before replacing the battery:

1.Remove all watches, rings or other metal objects.

2.Only use tools with insulated handles.

3.DO NOT lay tools or other metal parts on top of battery or any battery terminals.

4.Wear rubber gloves and boots.

5.Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of

ground. CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds are removed during installation and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit).

BATTERY REPLACEMENT PROCEDURE:

1.Turn off and unplug all connected equipments.

2.Turn the UPS off and unplug it from the AC power source.

3.Carefully turn the UPS upside down. Remove the 6 retaining screws and the cover.

4.Disconnect the black and red wires from the battery set.

5.Remove the battery protection cover and take out the battery set from the compartment.

6.Slide a new battery pack into the unit. Assemble the battery protection cover, cable, screws in the reverse sequence of above steps.

REMINDER: Recharge the unit for 4 – 8 hours to ensure the UPS performs expected runtime

STORAGE:

First turn off your UPS and disconnect its power

cord from the wall outlet. Disconnect all cables connected to the UPS to avoid battery drain. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to insure battery life. If the battery remains uncharged for an extended period of time, it may suffer permanent loss of capacity.

TROUBLE SHOOTING

Problem	Possible Cause	Solution
The UPS does not	Batteries are not fully	Recharge the battery by leaving the UPS
	charged.	plugged in.
perform expected
		Contact CyberPower Systems at
runtime.	Battery is slightly worn out.
		service@cyberpower-eu.com
	The on/off switch is
	designed to prevent	Turn the UPS off. Wait 10 seconds and then
	damage by rapidly turning it	turn the UPS on.
The UPS will not	off and on.
	The unit is not connected to	The unit must be connected to a 220-240V
turn on.
	an AC outlet.	50/60Hz outlet.
	The battery is worn out.	Contact CyberPower Systems at
		service@cyberpower-eu.com
	Mechanical problem.	Contact CyberPower Systems at
		service@cyberpower-eu.com
		Turn the UPS off and unplug at least one
	Circuit breaker is tripped due	piece of equipment. Wait 10 seconds, reset
Outlets do not	to overload	the circuit breaker and then turn the UPS on.
		Allow the unit to recharge for at least 4
provide power to	Batteries are discharged
equipment		hours.
	Unit has been damaged by	Contact CyberPower Systems at
	a surge or spike.	service@cyberpower-eu.com
	The serial/USB cable is not	Connect the serial/USB cable to the UPS
		unit and an open serial port on the back of
	connected.	the computer. You must use the cable that
		came with the unit.
PowerPanel®	The serial/USB cable is	Try another serial/USB port of your
Business Edition is	connected to the wrong	computer.
	port.
inactive (all icons
		Shutdown your computer and turn the UPS
are gray).	The unit is not providing
		off. Wait 10 seconds and turn the UPS back
	battery power.
		on. This should reset the unit.
	The serial cable is not the	You must use the cable included with the
	cable that was provided with
		unit for the software.
	the unit.

TECHNICAL SPECIFICATIONS

Model					PP1500E				PP2200E
Capacity	(VA)				1500VA				2200VA
Capacity	(Watts)				1000W				1600W
Input
Input Voltage Range								220-240Vac
Frequency Range								50/60 Hz
Output
On Battery Output Voltage					Pure Sine Wave at 230Vac +/- 7%
On Battery Output Frequency								50/60 Hz
Overload Protection				On Utility: Circuit Breaker, On Battery: Internal Current Limiting
Surge Protection and Filtering
Lightning / Surge Protection								Yes
Network Protection							RJ45 (One In/One Out)
Physical
Total # of UPS Receptacles							(8) IEC 320 C13
Maximum Dimensions							42.0cm*18.0cm*23.7cm
Weight (Kg)					25.4				31.1
Battery
Sealed Maintenance Free					12V / 7AHx4				12V / 9AHx4
Lead Acid Battery
User Replaceable					Yes, Hot Swappable Battery Pack
Typical Recharge Time								8 Hours
Warning Diagnostics
Indicators				Power On, Using Battery, AVR, Load Level, Battery Level
Audible Alarms					On Battery, Low Battery, Overload
Environmental
Operating Temperature						+32°F to 95°F ( 0°C to 35°C )
Operating Relative Humidity						0 to 95% NON-CONDENSING
Communication
PowerPanel® Business					Windows 98/ME/2000/NT/XP, Server 2003
Edition Software
Management
Auto-Charger								Yes
Auto-Restart								Yes
USB Interface								Yes
SNMP/HTTP Network								Optional
	DEFINITIONS FOR ILLUMINATED LED INDICATORS
		Using	Circuit						Condition
Power	AVR				Alarm
		Battery	Breaker
On
On	Off	Off		Set	Off				Normal
On	Slow	Off		Set	Off		AVR- Max. boost 13% of input voltage for output
							regulation while input voltage is from 5% to 14%
	flash
							under nominal.
On	Rapid	Off		Set	Off		AVR- Max. boost 26% of input voltage for output
							regulation while input voltage is from 15% to 26%
	flash
							under nominal.
ON	On	Off		Set	Off		AVR- Max. buck 10% of input voltage for output
							regulation while input voltage is from 7% to 22%
							over nominal.
Off	Off	On		Set	Two		Utility Failure- The UPS is providing battery
					Beeps		power to the Battery-Power Supplied outlets.
					Rapid		Utility Failure- The UPS is providing battery
Off	Off	On		Set			power.	Rapid beeps indicate the battery will run
					Beeps
							out of charge within a few minutes.
	On/ Off				Long		Overload- Turn the UPS off and unplug at least
On/Off		On/Off		Set			one piece of equipment from the UPS. Wait 5
	/Flash				Beep		seconds, reset the circuit breaker and restart the
							UPS.
					Long		Overload- Turn the UPS off and unplug at least
Off	Off	On		Up			one piece of equipment from the UPS. Wait 5
					Beep		seconds, reset the circuit breaker and restart the
							UPS.
Off	Off	Off		Set	Off		Surge Protection Malfunction- Power surge has
							damaged the unit. Please contact CyberPower
							Systems.

For more information, visit eu.cyberpowersystems.com or contact

CyberPower Systems B.V. Flight Forum 3545, 5657DW Eindhoven, The Netherlands Tel: +31 (0)40 2348170, E-MAIL: sales@cyberpower-eu.com

CyberPower Systems Inc. (USA) 4241 12th Avenue East Suite 400 Shakopee, MN 55379, U.S.A. Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL: sales@cyberpowersystems.com

Entire contents copyright ©2004 CyberPower Systems B.V., All rights reserved. Reproduction in whole or in part without permission is prohibited. PowerPanel® and PowerPanel® Plus are trademarks of CyberPower Systems (USA) Inc.

CyberPower warrants to you, the original purchaser, that CyberPower UPS will be free from defects in design, assembly, materials and workmanship for two years ( battery is only one year) from the date of original purchase. Any warranty services, please contact your local dealers or distributors