Manuals / Brands / Computer Equipment / Computer Hardware / CyberResearch / Computer Equipment / Computer Hardware

CyberResearch PCIDIO 24H, PCIDIO 48H, PCIDIO 96H 2.2Unpacking, Note:, 8 ∙ Installation, You are now ready to install your 24H/48H/96H series product

1 59

Download 59 pages, 360.35 Kb

2.2Unpacking

Your card contains sensitive electronic components that can be easily damaged by static electricity.

The card should be put on a grounded anti -static mat. The operator should wear an anti-static wristband, grounded at the same point as the anti -static mat.

Inspect the card module carton for obvious damage. Shipping and handling may cause damage to your module. Be sure there is no shipping and handling damage on the module before processing.

After opening the card module carton, extract the system module and place it only on a grounded anti-static surface with components side up.

Again inspect the module for damages. Press down on all the socketed IC's to make sure that they are properly seated. Do this only with the module place on a firm flat surface.

Note: DO NOT APPLY POWER TO THE CARD IF IT HAS BEEN DAMAGED.

You are now ready to install your 24H/48H/96H series product.

8 ∙ Installation

Contents

Digital I/O High-Density, PCI-Bus,Parallel Digital Board with 24 Channels, 24mA/Channel Sink 96 Channels, 24mA/Channel Sink Page • NOTICE • Page Table of Contents Installation Chapter 3 Registers Format Chapter 4 Operation Theorem Chapter 5 C/C++ Libraries Product Service Warranty How to Use This Guide Chapter 1, Introduction Chapter 2, Installation Chapter 3, Registers Format Chapter 4, Operation Theorem Introduction 1.1Features 1.1.1 Digital I/O Ports 1.1.2 Timer/Counter and Interrupt System 1.1.3 Miscellaneous 1.2Applications 1.3 Specifications 1.4Software Support 1.4.1 Programming Library 1.4.2 PCI LV: LabVIEW® Driver 1.4.3 PCI VEE: HP-VEEDriver 1.4.4 PCI DAQB: ActiveX Controls 1.4.5 DASY PRO 1.4.6 PCI DDE: DDE Server and InTouchTM Page Installation 2.1What You Have 2.2Unpacking 2.3PCB Layout 2.3.1PCIDIO 48H/24H PCB Layout 2.3.2 PCIDIO 96H PCB Layout 2.4Hardware Installation 2.5 Device Installation for Windows Systems 2.6Connector Pin Assignment 2.6.1Pin Assignment of PCIDIO 24H/48H/96H 2.6.1 Continued 14 ∙ Installation Page Page 2.7Jumpers Description 2.7.1 Power on Status of Ports 2.7.2 12V Power Supply Configuration 2.8Termination Boards Connection Page Page Registers Format 3.1PCI PnP Registers 3.2I/O Address Map Operation Theorem 4.1Digital I/O Ports 4.1.1Introduction 4.1.2 8255 Mode 4.1.3 Special Function of the DIO Signals 4.1.4 Digital I/O Port Programming 4.1.5 Control Word 4.1.6 Power on Configuration 4.1.7 Note for Output Data 4.2Timer/Counter Operation 4.2.1Introduction 4.2.2 General Purpose Timer/Counter 4.2.2 Cascaded 32 Bits Timer 4.2.3 Event Counter and Edge Control 4.3Interrupt Multiplexing 4.3.1Architecture 4.3.2 IRQ Level Setting 4.3.3 Note for Dual Interrupts 4.3.4 Interrupt Source Control 4.412V and 5V Power Supply C/C++ Libraries 5.1Libraries Installation 5.2Programming Guide 5.2.1Naming Convention 5.2.2 Data Types 5.3_DIO48H/96H_Initial 5.4Digital Input 34 ∙ C/C++ Libraries 5.5Digital Output 5.6Configuration Port 5.7Configuration Channel 38 ∙ C/C++ Libraries 5.8Set Interrupt Control 5.9Timer Start 5.10 Timer Read 5.11 Timer Stop 5.12 Cascaded Timer 5.13 Get IRQ Status 5.14 Clear IRQ 5.15 Software Reset 5.16 Interrupt Start under Windows 5.17 Interrupt Stop under Windows Diagnosis and Debug Product Service ¥ Returns and RMAs PLEASE CALL FOR AN RMA NUMBER Please make sure that the RMA number is prominently displayed on the outside of the box • Thank You •