DES-5024 Rear Panel | D-Link specs

Fast Ethernet Switching System User’s Guide

Rear Panel

The three pronged power plug, ventilation fan and the on/off switch are located at the rear of the DES-5024 displayed in Figure 2. The DES-5024 will work with AC in the range 100-240 VAC, 50-60 Hz. The power requirements are indicated on the rear panel of the DES-5024. When installing the DES-5024, leave enough room to allow you to plug in the power cable.

There are heat vents located on the sides. The fans and the vents help to cool the DES- 5024. Always leave two inches of space around the DES-5024 so that air can circulate and cool the DES-5024.

Fan

Power On/Off switch

Three pronged power plug

Figure 2: DES-5024 Rear Panel

Introduction

5

Image 13

D-Link manual DES-5024 Rear Panel

Contents

DES-5024 Fast Ethernet Switching System User’s Guide Link Limited Warranty Hardware North, Central, and South America Copyright Statement Wichtige Sicherheitshinweise Table of Contents Page Page Audience About This GuideOrganization Introduction FeaturesPage DES-5024 Front Panel Front Panel DES-5024 Rear Panel Rear Panel Updating Firmware Management MethodsLocal Console Management Telnet Management Unpacking the DES-5024 Installing the DES-5024 Installation Options Install Feet on Bottom Desktop/ Shelf Installation Attach Feet Rack Installation Attach Mounting Brackets Insert into Rack Installing Modules Remove Blank Bracket Insert Optional Module Power On Cable Specifications Connecting the DES-5024 to the NetworkCopper Cable Cable Diagram Fiber Optic Cable MDI-X Ports PortsFiber Optic Ports RS-232 Port DES-5024 to DES-5024 Connection Connecting the DES-5024 to other Switches and Hubs DES-5024 LEDs LEDs CPU Module Power LED Link Port 10/100-TX Module Col Port 100BASE-FX Module Lit Dark Act Port 1000BASE-SX Module Managing the DES-5024 ∙ Data bits ∙ Parity None ∙ Stop bits ∙ Flow Control None Local Console Management Telnet Log ∙ Default User Name D-Link ∙ Default Password D-Link Help Message Help Message Spacebar Panel Conventions Console Program System ConfigurationUser Account Management Spanning Tree Configuration 100BASE-FX/ 1000BASE-SX Switch Port ModuleSnmp Management Configuration Vlan Port Management System Reset System Configuration MenuFactory Reset to Default Config Values System Information Boot Prom Firmware Version Software UpdateSystem Information Menu Hardware Revision MAC Address LAN Default GatewaySystem Description System Name System Reset System Reset Factory Reset Factory Reset Factory Reset confirmation Advantages of Store and Forward System Rate ControlDisadvantages of Store and Forward Disadvantages of Cut-Through Advantages of Cut-Through Software Update menu Software Update Menu Transfer Firmware Xmodem User Account Change Menu User Account Management Confirm Password PasswordAccess Level Create New UserPage Status Delete UsersDelete Page Old Password Change PasswordNew Password Page Switch Port Configuration State Switch Port Configuration MenuPhysical Priority Port StateFlow Control Spanning Tree Configuration Menu Spanning Tree ConfigurationSTA Operation Levels Spanning Tree Algorithm Forward Delay TimeBridge Priority Root Cost Root Port Root Bridge Snmp Management Configuration Snmp Manager Setting Snmp Management Configuration MenuAccess Right Snmp Community String Authentication Failure Snmp Trap Manager SettingCold Start Link Change EventPage Vlan Port Management Vlan Port Management menu Vlan Port Management Menu New Vlan Name Create New VlanPort # TrunkGroupPage Vlan Name Delete Vlan Menu Virtual LAN Name Modify Vlan Menu Trunking Port Management menu Trunking Port Management Menu New Trunking Group Name Create New Trunking PortName Page Trunking Port Delete Trunking PortModify Trunking Port Modify Trunking Port Trunking Port Name ProblemSolution TroubleshootingPage Diagnostic LED Switch Specifications Appendix a DES-5024 Technical SpecificationsPort Specifications 10BASE-T EMI Fast Ethernet Switching System User’s Guide Performance Index Access Level User Name 50, 52