Dacor RR30NFS[-C], RR30NIFS[-C], RR30NIS[-C], RR30NS[-C] 3” Side Panels Removed, 3” Side Panels Installed, Top View - Downdraft ERV30[15] with Slide-In, Self-RimmingInstallation

Installation Specifications

Cabinet Cutouts for Self-Rimming Installation with Raised Vent (Models RR30NIS and RR30NIFS Only)

Countertop 1 5/8 (41.1 cm)

max. thickness

(see diagrams)

• Trim kit PN ATKR30SR is required for proper

installation of a raised vent with this range.

• The self-rimming installation of the RR30NI[F]

S range and ERV30[15] raised vent create a

“built-in” look where the range trim overlaps and

rests on the countertop on both sides and the

raised vent trim overlaps the countertop in back.

The ATKR30SR trim kit, installed on the back of

the range, will cover the front of the raised vent

chassis.

343/4”

(88.3 cm) to

367/8”

(93.7 cm)

1” min. (2.6 cm)

to any combustibles above counter both sides

Cut 3” dia. (7.6 cm) holes at back bottom of cabinet for ventilation.

Provide ventilation through cabient both sides,

7 square inches min. Location may vary.

Rear wall or	3/8” min. (1.0 cm)
countertop edge
	countertop overhang

•	IMPORTANT: When installing the range in this
	configuration, ventilation must be provided to allow
	for cooling of the ranges internal components. See
	diagram, left.
•	Observe all vertical cabinet clearances on
	page 5.
•	A self-rimming countertop configuration is required
	for raised vent installation. On installations with a
	raised vent, when sliding the range into position, it
	will stop when the rear of the control panel or side
	panels contact the notches toward the front of the
	countertop.

(6.7 cm)

27 1/2” (69.9 cm)

2 5/8”

raised vent opening

20

3/8”

25”

20

3/8”

(51.8 cm)

29 1/4” (74.3 cm)

(63.5

cm)

(51.8 cm)

to

countertop opening

max.

30 1/16” (76.2 cm)

23 3/8”

(59.4 cm)

cabinet opening

below countertop

Notch countertop

t

o width of cabinets

Cabinet face

Countertop front

below countertop

Top View - Downdraft ERV30[15] with Slide-In, Self-Rimming Installation,

3” Side Panels Installed

1” min. (2.6 cm)

Rear wall or

3/8” min. (1.0 cm)

to any combustibles

countertop edge

above counter both sides

countertop overhang

(6.7 cm)

27 1/2” (69.9 cm)

2 5/8”

raised vent opening

* To create a “built-in look” on the front of the

25”

23

3/8”

29 1/4” (74.3 cm)

cabinet, this dimension may be changed to 29 1/4”

(63.5

cm)

(59.4

cm)

countertop opening

(74.3 cm), with the width at the notches remaining

max.

30 1/16” (76.2 cm)*

30 1/16”. This configuration is only for models

cabinet opening

RR30NIS and RR30NIFS with the side panels

below countertop

behind the door removed.

Notch countertop

t

o width of cabinets

Cabinet face

Countertop front

below countertop

Top View - Downdraft ERV30[15] with Slide-In, Self-Rimming Installation,

3” Side Panels Removed

7