Dacor MRES30, rsd30, RSE30 door removed from the oven, wire securely clamped to bare, injury

30"

(762mm)

Range Top

Rear of Control

Panel/Oven Door

231/2"

(597mm)

269/16"

(675mm)

Removing the Oven Door

WARNINGS:

1.	Do not attempt to disengage
	the hinge catches with the
	door removed from the oven.
	The hinge springs could
	release causing personal
	injury.
2.	Do not lift or carry the oven
	door by the door handle.

4.	Do not install a fuse in the
	neutral or ground circuit. A
	fuse in the neutral or ground
	circuit may result in an
	electrical shock hazard.
5.	Do not ground the appliance
	to a gas supply pipe or hot
	water pipe.
6.	A grounded cold water pipe
	must have metal continuity to
	electrical ground and must not

	Max. depth
	to oven door
Door Opened	handle with
	door closed 45 1/4"
	(1149mm)

Overall Dimensions (Preference Models)

Isometric View

30"

(762mm)

Open the door to its fully opened position. Rotate the catch over the retaining arm on each hinge. Lift the oven door to about a 30 degree angle from the horizontal position. Pull the door away from the oven while continuing to lift.

be interrupted by insulating

materials. Any insulating

materials must be jumped

with a length of No. 4 copper

wire securely clamped to bare

metal at both ends.

Grounding Instructions (All Models) This appliance must be electrically grounded.

Range Top	23 1/2"
		(597mm)
			25 5/16"
Rear of Control			(643mm)
Panel/Oven Door
	Max. depth
	to oven door
	handle with
Door Opened	door closed

45 1/4" (1149mm)

Overall Dimensions (MRES Model)

Isometric View

Installing the Anti-Tip Bracket

WARNING:

This appliance require an anti- tip device. Before installing the range, you must locate and secure the anti-tip bracket to the floor.

When the range is slid into position in the cutout, the left rear leveling leg slides into this bracket to prevent the unit from tipping forward. The bracket location shown here will position the rear edge of the range top frame flush to the rear wall. From this position, the bracket allows for up to 5/8” (16mm) of forward movement of the range.

11/2”

(38mm)

19 7/16”	24”
	(610mm)
(494mm)

Front face	C
of cabinet
	L

Removing the Oven Door

Remove the Kick Panel (All Models)

Remove the screw at each top corner of the kick panel. Lift up slightly on the panel and pull forward to remove

Electrical Connection

NOTE:

See the range data plate for electrical specifications. See page 1 for location.

WARNINGS:

1.All of these range models must be connected to a grounded, metallic, permanent

wiring system. Alternatively, a grounding conductor should be connected to the grounding terminal or lead on the appliance.

3. Do not use an extension cord

With the range positioned directly in front of the cabinet cutout, feed the appliance conduit to the electrical junction box. Then, depending upon local codes, utilize one of the following techniques to connect the appliance to the electrical power supply:

A.Connecting to a Four-Wire Electrical System. (Recommended for All Models)

1.Separate the green and white appliance wires.

2.Connect the white appliance wire to the neutral (white) supply wire in the junction box.

3.Connect the black appliance wire to the black (L1) power supply wire in the junction box.

4.Connect the red appliance wire to the red (L2) power supply wire in the junction box.

5.Connect the green appliance wire to the green house grounding wire in the junction box.

	Cable from
	power supply
		Junction
		box
RED		WHITE
RED
		WHITE
GREEN		BLACK
GREEN
		BLACK
		Wire nut
		(4 places)
	Conduit from
	appliance

Connecting the appliance to a

four-wire power supply

(All Models)

2 3/16” 113/8”

(556mm) (289mm)

1”

(25mm)

with this appliance. Such use

may result in fire, electrical

shock, or other personal

Location of Anti-Tip Bracket

Top View

injury.