ELECTRICAL ADJUSTMENT

(4) FM DEVIATION

Adjustment Parts

Check Point

Measuring Equipment

Test Tape

Input Signal

R392

TJ396

Signal Gen. Oscilloscope

Blank Tape

Color Bar

 

 

 

 

 

vCONNECTION METHOD

TJ396

 

TJ302

 

 

CH-1

 

Oscilloscope

 

CH-2

R392

 

FM DEV

SIGNAL

GENERATOR

 

vADJUSTMENT PROCEDURE

1)Supply the Color Bar Signal to the VIDEO IN JACK, and set the VCR to the REC mode.

2)Connect the oscilloscope to TJ396 and trigger scope with a composite sync signal at TJ302.

3)Record the Color Bar Signal for a few minute and playback it. Then confirm that the playback video

output level (TJ396) is 2.0 ± 0.2Vp-p.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4) Adjust as follows if the playback video output level

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

is not 2.0 ± 0.2Vp-p.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-1)

Adjust R392 a little.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-2)

Record the Color Bar Signal for a few minute

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and playback it.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-3)

Confirm the playback video output level.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4-4)

Repeat the procedure of 4-1) to 4-3) until

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Horizontal :10 s/div

 

the playback video output level becomes 2.0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Vertical :0.5V/div

( 0.2Vp-p between sync tip and 100% white level.

TJ396

2.0V 0.2Vp-p

10

Page 11
Image 11
Daewoo DV-K580NZ-T service manual FM Deviation