DRY (Dehumidifier) Operating Instructions

NOTE: The exhaust hoses do not have to be installed during dehumidifier mode.

Both internal and external water tanks must be installed during dehumidifer mode.

1)Press the I/O (on/off) key pad to switch on the unit.

2)Press the MODE key until the word DRY (Dehumidifying) appears in the display window. Each depression of the MODE key will advance to a different mode setting (Cool-Dry-Fan).

3)Press the appropriate (TEMP / TIMER ADJ) key to select a (relative humidity) operating setting between 35% ~ 90% RH (adjustable in increments of 5%)

For continuous (non-stop) dehumidifer operation

press the (TEMP / TIMER ADJ) key pad until the symbol “- - “ appears in the display window.

NOTE: The compressor will not cycle off during “continuous” mode.

The set relative humidity level will flash in the display window for approximately 5 seconds then automatically revert back to display actual room ambient relative humidity conditions. NOTE: The set operating RH level must be programed within the 5 second (flashing) condition. To view the “set” relative humidity program any time, press either of the TEMP/TIMER ADJ buttons.

NOTE: There is no fan speed adjustment during dehumidifying mode. (the fan speed is factory set for “low”)

The blue (RUN) indicator light illuminates indicating dehumidifying mode is operational (there may be a slight delay of 10-30 seconds before the cycle begins, this is normal).

IMPORTANT: The relative humidity setting selected should always be set a few degrees lower than the room ambient relative humidity conditions, to ensure normal dehumidifying operation. NOTE: it is not recommended to operate your Dehumidifier, below temperatures of 15.5°C (60°F), this could result in icing-up conditions of the evaporator coils, and minimize efficiency.

4)Condensed water will be accumulated in the external / internal water tanks. When the external tank is full, water will backflow into the internal tank. When the internal tank is full, the unit will alarm (beep) for 20 deconds and the Water Full indicator light will illuminate. At this time dehumidification will stop immediately. However, the fan motor will continue to operate (this is normal). Carefully remove both water tanks from the cabinet, dispose of the water. Replace the water tanks back to their original positions and the Dehumidifying process will automatically resume. It may take 3-5 minutes for the compressor to re-start. This is normal.

5)This unit also has provisions for a continuous “drain” option (for basement applications having a floor drain). The required drain hose extension is not included with this unit. It can be purchased through any local Hardware Store. Drain Hose Specifications: Standard garden hose.

For continuous direct drain operation. Remove (unscrew) the drain cap at the back of the cabinet located directly above the external tank quick connect. Attach suitable length (of garden hose) to the direct drain fitting. (do not over tighten) Position the open end of the drain hose as close as possible to the floor drain. Check the hose connection for leaks.

NOTE: Direct drain operation is intended for floor drain applications only. Direct drain operation should not be used in stem pipe and/or sink applications.

11

Page 22 Page 24
Page 23
Image 23
Danby DPAC10030 manual
Page 22 Page 24

DPAC10030 specifications

The Danby DPAC10030 is a powerful portable air conditioner designed for residential and small office environments, providing cooling relief during the hot summer months. With its sleek design and robust features, the DPAC10030 ensures comfort while offering efficient performance.

At the heart of the Danby DPAC10030 is its cooling capacity of 10,000 BTU, making it suitable for spaces up to 300 square feet. This ability allows it to cool down a room rapidly, providing immediate relief from heat. The unit operates quietly, which is ideal for bedrooms or study areas, ensuring that users can enjoy a peaceful environment without disruptive noise.

One of the standout features of the DPAC10030 is its innovative dual-hose system, which enhances its cooling efficiency. Unlike traditional single-hose models that draw in air from the room and vent it outside, the dual-hose design allows for one hose to pull the hot air out while the other brings in fresh air from outside. This not only cools the space more effectively but also helps maintain a more balanced indoor environment.

The Danby DPAC10030 comes equipped with user-friendly electronic controls, including an LED display that makes it easy to set your desired temperature and operating mode. It offers multiple fan speeds and cooling settings, allowing users to customize the environment to their preferences. Additionally, the unit features a 24-hour programmable timer, which enables users to control when the air conditioner turns on and off, conserving energy while ensuring comfort.

For those who prioritize energy efficiency, the DPAC10030 offers a commendable Energy Efficiency Ratio (EER). Lower energy consumption translates to reduced electricity bills, making it an economically viable choice for cooling needs. The unit also includes a programmable thermostat that maintains your desired temperature with minimal effort.

In terms of mobility, the Danby DPAC10030 features built-in casters, allowing for easy movement from room to room, as well as side handles for convenience. The compact design ensures that it can fit through doorways without hassle.

Moreover, maintenance is straightforward with an easy-to-clean washable filter that helps trap dust and allergens, improving indoor air quality.

In summary, the Danby DPAC10030 is a versatile and efficient portable air conditioner that combines convenience and performance. Whether for home use or in a small office, its powerful cooling capabilities, user-friendly features, and energy-efficient technology make it an excellent choice for those seeking reliable relief from the heat.
Top Page Image Contents