13.When the wall mounting bracket is securely screwed to the wall, line up the speaker’s protruding Mounting Screws with the keyhole slots on the wall mounting bracket. Let the speaker slide straight down, allowing the screw heads to slip behind the smaller end of the keyhole slots. Gently push the bottom front edge of the speaker toward the wall until the speaker snaps onto the lower lip of the bracket.
Mounting the SSA to an articulating TV bracket
If you have a Plasma or LCD TV that is attached to the wall via a
Using the Leveling Feet
If you are going to use the speaker on a TV, shelf or table, first attach the
SSA-42
wire has some indicator (such as
FRONT | CENTER | SURROUND | S | URR. BACK/REA |
|
| |||||
R |
| ||||||||||
|
| ||||||||||
+ RIGHT | LEFT |
| RIGHT | LEFT |
|
| HT | LE |
|
|
|
| RIG | FT |
|
| |||||||
|
|
|
|
|
–
SPEAKERS
If you have a 6.1 or 7.1 channel receiver, connect the SSA’s surround channel inputs to the “Surround” outputs of your receiver, not the “Rear” or “Surround Back” outputs.
To connect wire to the binding post [see figure above], unscrew the knurled nut and insert the bare wire into the hole near the base of the binding post. Do not insert the insulated part of the wire into the hole as this will not give you a good connection. Twist the nut back down the binding post until it firmly meets the wire. Do not over tighten.
Connect a single RCA cable from the “SUB OUT” of your receiver to the LFE input of the subwoofer (not included). This connecting method bypasses the subwoofer’s internal “crossover” or low pass filter and relies on the crossover filter built into your receiver. NOTE: Make no other signal connections. Do not use speaker wire to make the connection to the subwoofer
Connecting the SSA
Your Mythos SSA has one pair of
SSA-42
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| + SURROUND RIGHT – + FRONT RIGHT – |
| + CENTER – |
| + FRONT LEFT – | + SURROUND LEFT – | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To start, strip 1/2" (3 mm) of insulation from each speaker wire to expose the bare metal wire and twist each of the individual
95
40150
Variable
Low Pass Crossover
LFE
IN
High Level
LeftRight
+
In
–
conductors into single
Note that one of the terminals for each channel is marked with red band (+) and the other is marked with black band
(–)terminal of your amplifier or receiver to the black
Automatic
Power
ON/OFF
Out
–
+
P r o C i n e m a ®
S u b w o o f e r
A c t i v e C r o s s o v e r
a n d P o w e r A m p l i f i e r
120V 80Hz | T 3.2A L 250V |
|
| COMPONENT VIDEO |
|
|
|
|
|
|
|
|
MULTI INPUT | AUDIO | VIDEO |
|
|
|
|
|
|
|
|
|
| FRONT LEFT | FRONT RIGHT | SURROUND RIGHT | SURROUND LEFT |
| ||||
| SUBWOOFER | + | – | + | – | + | – | + | – | IMPEDANCE SELECTOR |
| (LFE) | |||||||||
| OUTPUT |
|
|
|
| CENTER |
| – |
|
|
AUDIO |
|
|
|
| + |
|
|
|
|
RECEIVER
SUBWOOFER
3