Dell 7x0N manual #$#%$$$$$$&$ +,*--./ #$0$1$22$$2$%$1%$ #$0$1$22$$2$%$1%$2

'￿￿￿￿￿￿￿￿￿￿￿(￿￿'￿￿￿￿￿￿￿￿

To configure the LECS address for your ATM adapter, use the elconfig set command.

Command syntax: The elconfig set command has the following syntax:

￿￿'￿￿￿￿,￿%￿￿￿￿￿￿'%￿￿￿￿￿￿￿￿￿￿￿￿￿=￿￿.￿￿￿>￿￿.￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

ATM_address is the ATM address of the LECS on the network.

unit_number is the unit designator for the ATM adapter in the filer.

The following command sets the LECS address to the well-known ATM address for the adapter in slot 2:

￿￿'￿￿￿￿,￿%￿￿￿￿￿￿'%￿￿.￿￿￿>￿￿.￿￿￿￿￿￿￿￿￿

If the LECS on your network does not use the well-known address, specify this address in place of “wellknown,” as shown in the following command:

￿￿'￿￿￿￿,￿%￿￿￿￿￿￿'%￿

￿8￿￿￿8"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿

Knowing the LECS address, the system can now determine all existing ELANs, as well as the ATM address of the LES. However, the LAN Type remains unknown until you configure the adapter to join the ELAN, which is discussed in “Configuring the ATM Adapter for an ELAN,” found later in this document.

To check the state of all adapters in the filer, use the elconfig show command.

Command syntax: The elconfig show command has the following syntax:

￿￿'￿￿￿￿,￿%-￿.￿￿￿￿￿

The abbreviated sample output (showing ELANs available through the LECS for Adapter 2 only) from this command is as follows:

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿ !￿"#$￿￿#%$￿￿$￿￿￿￿￿￿$￿￿￿￿$￿￿￿￿$￿￿￿￿$￿￿￿￿&￿￿￿￿￿￿'$￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿()￿￿￿￿￿￿￿￿￿￿￿(*￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿+￿￿￿￿,*(-￿￿￿-￿.￿￿/￿￿ "#$￿￿￿0$1￿$22￿'￿￿$￿￿￿￿$2￿'￿$"￿'%$￿￿￿￿"1'￿"￿'%$'"

￿3￿￿￿2￿￿￿￿￿￿￿￿￿￿￿￿-￿.￿￿/￿￿

"#$￿￿￿0$1￿$22￿'￿￿$￿￿￿￿$2￿'￿$"￿'%$￿￿￿￿"1'￿"￿'%$2￿

￿￿￿￿￿￿￿,*(-￿￿￿￿￿￿￿-￿.￿￿/￿￿￿￿￿￿

"#$￿￿￿0$1￿$22￿'￿￿$￿￿￿￿$2￿'￿$"￿'%$￿￿￿￿"1'￿"￿'%$''

Dell PowerVault 7x0N Systems — Connecting to ATM and FDDI Networks 9