Manuals / Dell / Computer Equipment / Personal Computer

Dell T5610 owner manual Press down on the latch and lift up the cables

Models: T5610

1 73

Download 73 pages 16.47 Kb

Page 16

Image 16

6.Press down on the latch and lift up the cables.

7.Lift up the release latch on top of the optical-drive cage.

8.Holding the release latch, slide the optical-drive cage from the optical-drive compartment.

Page 16

Image 16

Dell T5610 Press down on the latch and lift up the cables, Lift up the release latch on top of the optical-drive cage

Contents

Dell Precision Workstation T5610 Owners Manual Regulatory Model D01T Regulatory Type D01T003Notes, Cautions, and Warnings 2 Removing and Installing Components Contents1 Working on Your Computer 4 System Setup 5 Diagnostics6 Troubleshooting Your Computer 7 Technical SpecificationsWorking on Your Computer Before Working Inside Your ComputerTurning Off Your Computer After Working Inside Your ComputerPage Page Removing and Installing Components Recommended Tools1. Follow the procedures in Before Working Inside Your Computer Removing the Power Supply Unit PSUSystem Overview Installing the Power Supply Unit PSU 2. Follow the procedures in After Working Inside Your Computer4. Hold the handle bar to slide the PSU out of the computer 1. Hold the PSU handle and slide the PSU into the computerRemoving the Cover 1. Follow the procedures in Before Working Inside Your Computer2. Lay down the computer on its side with the latch facing up 3. Lift up the cover-release latchInstalling the Cover 3. Follow the procedures in After Working Inside Your ComputerRemoving the Front Bezel 1. Follow the procedures in Before Working Inside Your ComputerInstalling the Front Bezel 4. Follow the procedures in After Working Inside Your ComputerRemoving the Optical Drive 1. Follow the procedures in Before Working Inside Your Computer4. Unthread the cables from the latches 6. Press down on the latch and lift up the cables 7. Lift up the release latch on top of the optical-drive cageInstalling the Optical Drive 6. Follow the procedures in After Working Inside Your ComputerRemoving the Hard Drive 1. Follow the procedures in Before Working Inside Your ComputerInstalling the Hard Drive 1. Follow the procedures in Before Working On Your ComputerRemoving the Thermal Sensor 6. Follow the procedures in After Working Inside Your ComputerInstalling the Thermal Sensor 4. Follow the procedures in After Working Inside Your ComputerRemoving the Input/Output I/O Panel 1. Follow the procedures in Before Working On Your Computer2. Remove a. cover b. front bezel 3. Remove the screws that secure the USB 3.0 module to the I/O panelInstalling the Input/Output I/O Panel 7. Follow the procedures in After Working Inside Your ComputerInstalling the Air Tunnel Removing the Air TunnelRemoving the Memory 1. Follow the procedures in Before Working On Your ComputerInstalling the Memory Removing the Coin-Cell BatteryInstalling the Coin-Cell Battery 4. Follow the procedures in After Working Inside Your ComputerRemoving the Heatsink 1. Follow the procedures in Before Working Inside Your Computer2. Remove the cover 3. Disconnect the heatsink cable from the system board5. Follow the procedures in After Working Inside Your Computer Installing the HeatsinkRemoving the Heatsink Fan Installing the Heatsink Fan 4. Slide the heatsink fan from the heatsink assembly1. Slide the heatsink fan into heatsink assembly 3. Install a. heatsink b. coverRemoving the Processor 1. Follow the procedures in Before Working Inside Your ComputerInstalling the Processor Removing the System Fan6. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer4. Remove the screw that secures the metal plate to the system fan 5. Press the latches on either side of the metal plate to release it7. Remove the screws that secure the drive bay 6. Lift the metal plate out of the chassis8. Slide the latch out to release the air baffle 10. Remove the PSU cable from the clips 9. Remove the air baffle out of the computer11. Disconnect the system-fan cables from the system board CAUTION Using excessive force may damage the grommets Installing the System Fan 11. Follow the procedures in After Working Inside Your ComputerRemoving the PSU Card 1. Follow the procedures in Before Working On Your Computer3. Slide the baffle cover from its slot towards the front 5. Disconnect the power cables from the system board4. Remove the baffle cover from the computer Installing the PSU Card Removing the Speaker6. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working On Your ComputerInstalling the Speaker 2. Connect the speaker cable to the system board 3. Install the cover4. Follow the procedures in After Working Inside Your Computer 3. Disconnect the speaker cable from the system boardRemoving the System Board 1. Follow the procedures in Before Working Inside Your Computer2. Remove a. cover b. coin-cell battery c. PCI card d. memory modules e. thermal sensor f. air tunnel if available g. heatsink fan4. Disconnect the cables connected to the system board 5. Remove the screws that secure the system boardInstalling the System Board 6. Slide the system board towards the system-fan assembly7. Lift the system board away from the chassis 2. Tighten the screws to secure the system board to the chassisSystem Board Components 4. Install a. processor b. memory modules c. coin-cell batterym. thermal sensor n. cover o. power supply unit PSU 5. Follow the procedures in After Working Inside Your Computer7. USB 3.0 front-panel connector 11. processor socket 13. front-panel audio connector15. hard-drive HDD1 fan connector 17. DIMM slots 19. DIMM connectors 21. PSWD jumper 23. system fan 3 connectorPage Additional Information Power Supply Unit PSU LockMemory Module Guidelines Page Boot Sequence System SetupNavigation Keys System Setup Options Table 3. System Configuration NOTE If the hard drives are connected to a RAID controller card Table 4. Video Table 5. SecurityTable 6. Secure Boot Table 7. PerformanceDefault Setting Enable Hardware Prefetch Default Setting Enable Dell Reliable MemoryTable 9. POST Behavior Table 10. Virtualization SupportUpdating the BIOS System and Setup Password Assigning a System Password and Setup PasswordDeleting or Changing an Existing System and/or Setup Password Disabling a System Password1. Follow the procedures in Before Working Inside Your Computer 11. Follow the procedures in After Working Inside Your ComputerPage Diagnostics Enhanced Pre-Boot System Assessment ePSA DiagnosticsPage Troubleshooting Your Computer Diagnostic LEDsA possible graphics card failure has occurred Error Messages Errors That Halt Your Computer CompletelyErrors That Do Not Halt Your Computer Errors That Soft Halt Your ComputerTable 15. Errors that do not halt your computer Table 16. - Errors that soft halt your computerDell Reliable Memory Technology RMT has discovered and isolated errors in system memory. You may continue to work. Memory module replacement is recommended. Please refer to the RMT Event log screen in BIOS setup for specific DIMM information Page Technical Specifications Table 17. ProcessorTable 18. System Information Table 19. MemoryTable 20. Video Table 21. AudioTable 22. Network Table 23. Expansion InterfacesTable 24. Drives Table 25. External Connectorssupports one 5.25-inches SATA device or supports one Table 26. Internal Connectors two 164-pin connectors four when optional second processor isblinking amber light - indicates a problem has occurred with the solid amber light - the computer does not start, indicating a problemTable 27. Controls and Lights amber/blinking light - see the service manual for specific diagnostic Table 28. Power4015.3 BTU/Hr at 100 VAC 4365.5 BTU/Hr at 107 VAC40 G +/- 5% with pulse duration of 2 msec +/- 10% equivalent to Table 30. Environmental105 G +/- 5% with pulse duration of 2 msec +/- 10% equivalent to Page Contacting Dell 1. Visit dell.com/support