Manuals / Dell / Computer Equipment / Laptop

Dell W04C owner manual Performance, Power Management

Models: W04C

1 59

Download 59 pages 18.68 Kb

Page 47

Table 6. Performance

Option	Description

	• Reset All Keys- Resets to default setting
	• Delete All Keys- Deletes all the keys
		NOTE: If you disable the Custom Mode, all the changes made will be erased and
		the keys will restore to default settings.
Table 6. Performance

Option	Description

Multi Core Support	Specifies whether the process will have one or all cores enabled. The performance of
	some applications will improve with the additional cores.
	• All - Enabled by default
	•	1
	•	2
Intel SpeedStep	Allows you to enable or disable the Intel SpeedStep mode of the processor. This
	option is enabled by default.
C States Control	Allows you to enable or disable the additional processor sleep states. This option is
	enabled by default.
Limited CPUID Value	Allows you to limit the maximum value of the Standard CPUID Fuction support. Some
	operation systems will not complete installation when maximum CPUID Function
	supported is greater than 3.
	• Enable CPUID Limit - This option is disabled by default
Intel TurboBoost	Allows you to enable or disable Intel TurboBoost mode of the processor. This option
	is enabled by default.
	• Disabled - Does not allow the TurboBoost driver to increase the performance
		state of the processor above the standard performance.
	• Enabled - Allows the Intel TurboBoost driver to increase the performance of the
		CPU or graphics processor.
Hyper-Thread Control	Allows you to enable or disable the Hyper-Threading technology. This option is
	enabled by default.
Rapid Start Technology	Improves the battery life automatically by putting system into a low power state
	during Sleep, after a user-specified amount of time. Some increase in resume time
	from Sleep state may be experience, but the average resume times should be faster
	than the resume from Hibernate. The timer can be set starting from the value “0”. By
	default, this option is disabled.
Table 7. Power Management

Option	Description

AC Recovery	Specifies how the computer will respond when AC power is applied after an AC
	power loss. You can set the AC Recovery to:
	•	Power Off (default)
	•	Power On

47

Image 47

Dell W04C owner manual Performance, Power Management

Contents

Regulatory Model W04C Regulatory Type W04C002 Notes, Cautions, and Warnings 1 Working on Your Computer Contents2 Removing and Installing Components 5 Contacting Dell Installing the Antenna Module3 System Setup 4 Technical SpecificationsBefore Working Inside Your Computer Working on Your Computer2. Click Shut Down Recommended ToolsTurning Off Your Computer Important Information After Working Inside Your ComputerFigure 1. Inside View Removing and Installing ComponentsSystem Overview Removing the VESA Stand 1. Follow the procedures in Before Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer Installing the VESA Stand4. Follow the procedures in After Working Inside Your Computer Removing the Back Cover1. Follow the procedures in Before Working Inside Your Computer Installing the Back CoverRemoving the Memory 4. Follow the procedures in After Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer Installing the Memory5. Follow the procedures in After Working Inside Your Computer Removing the VESA Mount Bracket1. Follow the procedures in Before Working Inside Your Computer Installing the VESA Mount BracketRemoving the Power and On-Screen Display OSD Buttons Board 4. Follow the procedures in After Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer Installing the Power and OSD Buttons BoardRemoving the System-Board Shield 4. Follow the procedures in After Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer Installing the System-Board ShieldRemoving the Converter Board 4. Follow the procedures in After Working Inside Your ComputerRemoving the Optical Drive Installing the Converter BoardRemoving the Coin-Cell Battery Installing the Coin-Cell Battery5. Slide and lift the optical drive from the computer 1. Follow the procedures in Before Working Inside Your Computer Installing the Optical Drive7. Follow the procedures in After Working Inside Your Computer Removing the Hard DriveInstalling the Hard Drive 1. Follow the procedures in Before Working Inside Your Computer Removing the Intrusion Switch7. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer Installing the Intrusion SwitchRemoving the Wireless Local Area Network WLAN Card 4. Follow the procedures in After Working Inside Your Computer5. Follow the procedures in After Working Inside Your Computer Installing the WLAN CardRemoving the Heat-Sink Assembly Installing the Heat-Sink Assembly4. Follow the procedures in After Working Inside Your Computer Installing the Processor FanRemoving the Power-Supply Fan Removing the Processor Fan5. Follow the procedures in After Working Inside Your Computer Installing the Power-Supply Fan1. Follow the procedures in Before Working Inside Your Computer Removing the I/O Board Shield7. Disconnect the power-connector cable from the system board 1. Follow the procedures in Before Working Inside Your Computer Installing the I/O Board ShieldRemoving the Power Supply Unit PSU 7. Follow the procedures in After Working Inside Your ComputerInstalling the Power Supply Unit Removing the Speakers Installing the Processor6. Follow the procedures in After Working Inside Your Computer Removing the Processor4. Follow the procedures in After Working Inside Your Computer Installing the Speakers1. Follow the procedures in Before Working Inside Your Computer Removing the System BoardSystem Board Layout 7. processor heat sink fan connector 8. camera connector 1. SATA ODD power connector 2. SATA HDD connector3. SATA HDD power connector 4. SATA ODD connector 5. graphic heat sink fan connector 6. intrusion switch connector1. Follow the procedures in Before Working Inside Your Computer Installing the System BoardRemoving the Heat Sink Graphics Card 5. Follow the procedures in After Working Inside Your Computer5. Remove the heat sink from the system board Installing the Heat Sink Graphics Card3. Connect the fan cable 4. Install a. system board b. power-supply fan c. converter board1. Follow the procedures in Before Working Inside Your Computer Removing the Antenna Module5. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer Installing the Antenna ModuleRemoving the Display Panel 4. Follow the procedures in After Working Inside Your Computer5. Lift the display panel from the chassis Installing the Display Panel 1. Follow the procedures in Before Working Inside Your Computer Removing the Camera7. Follow the procedures in After Working Inside Your Computer 4. Follow the procedures in After Working Inside Your Computer Installing the CameraNavigation Keys System SetupBoot Sequence System Setup Options Table 3. System Configuration Table 4. Security Computrace Service from Absolute Software Table 5. Secure Boot Table 6. Performance Table 7. Power ManagementTable 8. POST Behavior POST Hotkeys Description OptionDescription OptionSystem and Setup Password Updating the BIOSDeleting or Changing an Existing System and/or Setup Password Assigning a System Password and Setup Password5. Press Esc and a message prompts you to save the changes Technical Specifications Table 19. Cards Volume up/down buttons Windows 7 only, program menus, andTable 17. Audio Table 18. CommunicationsTable 24. Camera optional Table 22. Ports and ConnectorsTable 23. Power Table 26. Physical DimensionsTable 27. Controls and Lights White light - Solid white light indicates power-on state blinking8.10 kg to 8.76 kg 17.86 lb to 9.19 kg to 9.84 kg 20.26 lb toSpecification Feature1. GO to dell.com/support Contacting Dell