DeLonghi ECAM45.760 Menu Settings, Rinsing, Descaling, Install filter, Auto-start, Adjust time

Danger of burns!

During rinsing, a little hot water flows from the coffee spouts. Avoid contact with splashes of water.

• To turn the appliance off, press the button (fig. 8).

•The message “Turning off, Please wait” is displayed: if fea- tured, the appliance completes a rinse cycle and then goes off (standby).

Please note!

If you will not be using the appliance for some time, unplug from the mains socket:

•first turn the appliance off by pressing the button (fig. 8);

•release the main switch at the back of the appliance (fig. 2).

Important!

Never press the main switch while the appliance is on.

MENU SETTINGS

When you access the settings menu by pressing the MENU/ESC button, scroll the menu items by pressing < or > (fig. 9).

Rinsing

Use this function to deliver hot water from the spout to heat the internal circuit and make the coffee delivered hotter.

To enable the function, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press < or > (fig. 9) until “Rinsing” is displayed;

3.Press the OK button: “Confirm?” will be displayed.

4.Press the OK button (fig. 10): after a few seconds, hot water flows out of the spout, heating the internal circuit and ma- king the coffee delivered hotter.

Please note!

Press any button to stop hot water delivery at any time.

Descaling

For instructions on descaling, see page 18.

Install filter

For instructions on how to install the filter, see the section “Water softener filter” (page 19).

Replacing the filter (if installed)

For instructions on how to replace the filter, see the section “Re- placing the filter” (page 20).

1.Press the MENU/ESC button to enter the menu;

2.Press < or > (fig. 9) until “Adjust time” is displayed;

3.Press the OK button (fig. 10): the hours flash;

4.Press < or > (fig. 9) to change the hours;

5. Press the OK button to confirm: the minutes flash;

6.Press < or > (fig. 9) to change the minutes;

7.Press the OK button to confirm.

This sets the time. Press the MENU/ESC button to exit the menu.

Auto-start

You can set the auto-start time in order to have the appliance ready at a certain time (for example in the morning) so you can make coffee immediately.

Please note!

To enable this function, the time must already be set correctly.

To enable auto-start, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press < or > (fig. 9) until “Auto-start” is displayed;

3.Press the OK button. “Enable?” is displayed;

4.Press the OK button to confirm;

5.Press < or > to choose the hours;

6.Press the OK button to confirm;

7.Press < or > (fig. 9) to change the minutes;

8.Press the OK button to confirm;

9.Then press the MENU/ESC button to exit the menu.

Once the time has been confirmed, activation of auto-start is

indicated by the symbol displayed alongside the time. To disable the function:

1.Select auto-start from the menu;

2.Press the OK button. “Disable?” is displayed;

3.Press the OK button to confirm.

The symbol is no longer displayed.

Auto-Off (standby)

Auto-off mode can be set, so that the appliance switches off when not used for 15 or 30 minutes, or 1, 2 or 3 hours.

To programme Auto-off, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press < or > (fig. 9) until “Auto-off” is displayed;

3.Press the OK button;

4.Press < or > (fig. 9) until the required operating time (15 or 30 minutes, or 1, 2 or 3 hours) is displayed;

5.Press the OK button to confirm;

6.Then press the MENU/ESC button to exit the menu.

Auto-off is programmed.

Adjust time	Cup warmer
To adjust the time on the display, proceed as follows:	This function allows the cup warmer to be enabled or disabled.

10