DeLonghi GB Energy Saving, Setting the temperature, Setting water hardness, Beep, Cup lighting

3.	Press the	button. “Disable?” is displayed (or “En-
	able?” if the function has been disabled);
4.	Press the	button to disable (or enable) the func-
	tion.

5.Press the MENU/ESC button to exit the menu. Warming the cups keeps the coffee hot.

Energy Saving

Use this function to enable or disable energy saving mode. When enabled, the function reduces energy consumption in compliance with European regulations.

To disable (or enable) “energy saving” mode, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Energy saving” is displayed;

3.	Press the	button. “Disable?” is displayed (or “En-
	able?” if the function has been disabled);
4.	Press the	button to disable (or enable) energy
	saving mode;

5.Then press the MENU/ESC button to exit the menu.

When the function is enabled, if the machine is not used for about 1 minute, “Energy Saving” is displayed.

Please note!

•When in energy saving mode, a few seconds elapse before the first coffee, cappuccino or milk based coffee is delivered as the appliance must heat up again.

•To prepare any drink, press any button to exit energy saving, then press the button corresponding to the drink you want to make.

•If the milk container is inserted, “Energy saving” is not activated.

Setting the temperature

To modify the temperature of the water used to make the cof- fee, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Set temperature” is displayed;

3.Press the button;

4.Press the HOT MILK or LATTE button until the required temperature (●= low; ●●●●= high) is displayed;

5.	Press the	button to confirm;
6.	Press the	MENU/ESC button to exit the menu.

Setting water hardness

For instructions on setting water hardness, see page 20.

Beep

This enables or disables the beep emitted by the machine each time the buttons are pressed or an accessory is inserted/ removed. The beep is enabled by default.

To disable or re-enable the beep, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Beep”

	is displayed;
3.	Press the	button. “ Disable?” or “ Enable?” is dis-
	played;
4.	Press the	button to enable or disable the beep;
5.	Press the MENU/ESC button to exit the menu.

Setting the language

To change the language for the display, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Set language” is displayed;

3.Press the button;

4.Press the HOT MILK or LATTE button until the required language is displayed;

5. Press the button to confirm;

6.A message confirming the language installed is displayed;

7.Then press the MENU/ESC button to exit the menu.

Cup lighting

This function enables or disables the cup lighting. The lighting is enabled by default.

The lights come on each time coffee and drinks with milk are made and during each rinse cycle.

To disable or re-enable this function, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “Cup lighting” is displayed.

3.	Press the	button. “ Disable?” or “ Enable?” is dis-
	played;
4.	Press the	button to enable or disable the cup
	lighting;
5.	Press the MENU/ESC button to exit the menu.

Default values (reset)

This resets all menu settings and programmed quantities back to the default values (with the exception of the language which remains as previously set).

To reset the default values, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the HOT MILK or LATTE button (fig. 8) until “De- fault values” is displayed;

3.Press the button;

4.The message “Confirm?” is displayed.

11