DeLonghi GB, DE, ECAM28.46X, 10.13 manual Technical Specification, Disposal, Removing the filter

the openings at the side		35
for more than a minute
(fig. 34).
4. Extract the tank from the
appliance and fill	with
water.
5. Insert the filter in the
water tank and immerse
it completely for	about
ten minutes, sloping it to		36A
enable the air bubbles to

escape (fig. 35).

6.Insert the filter in the fil- ter housing and press as

	far as it will go (fig. 36A)
7.	Close the tank with the	36B
	lid, then put the tank
	back in the machine (fig.
	36B).
When you install the filter,
you must notify the appliance
of its presence.
8.	Press the MENU/ESC button to enter the menu;
8.	Press the HOT MILK or LATTE button (fig. 8) until “Install
	filter” is displayed;

10.Press the button;

11.The message “Enable?” is displayed.

12.Press the button to confirm the selection. “Hot water Confirm?” is displayed;

13.Position a container under the hot water spout (min. ca- pacity: 500 ml);

14.Press the button to confirm the selection. The appliance begins hot water delivery and the message “Please wait” is displayed;

15.After delivery, the appliance returns automatically to the “Ready for coffee” position.

The new filter is active. You can now use the coffee maker.

Replacing the filter

When “REPLACE FILTER” is displayed, after two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the filter:

1.Extract the tank and exhausted filter;

2.Take the new filter out of its packet and proceed as illustrated in points 2, 3, 4, 5 and 6 in the previous section.

3.Position a container with a minimum capacity of 500 ml under the hot water spout.

4.Press the MENU/ESC button to enter the menu;

5.Press the HOT MILK or LATTE button until “Replace filter “ is displayed.

6.Press the button;

7.The message “Confirm?” is displayed.

8.Press the button to confirm the selection;

9.“Hot water… Confirm?” is displayed.

10.Press the button to confirm the selection. the appliance begins delivering hot water and the message “Please wait “ is displayed.

11.After delivery, the appliance returns automatically to the “ready for coffee” position.

The new filter is now active and you can use the coffee maker.

Removing the filter

If you want to continue using the appliance without a filter, you must remove it and notify the appliance of its removal as follows:

1.Extract the tank and exhausted filter;

2.Press the MENU/ESC button to enter the menu;

3.Press the HOT MILK or LATTE button (fig. 8) until “Install filter Enabled” is displayed;

4.Press the button

5.“Disable?” is displayed;

6.Press the button to confirm and the MENU/ESC button to exit the menu.

TECHNICAL SPECIFICATION

Voltage:	220-240 V~ 50/60 Hz max. 10A
Absorbed power:	1450W
Pressure:	15 bar
Water tank capacity:	2.0 litres max.
Size Lxhxd:	238x350x445 mm
Cable length:	1.80 m
Weight:	11.8 kg
Beans container capacity:	250 g max.

The appliance complies with the following EC directives:

•EC Regulation 1275/2008 for standby;

•Low Voltage Directive 2006/95/EC and subsequent amendments;

•EMC directive 2004/108/EC and subsequent amendments

•Materials and accessories coming into contact with food conform to eec regulation 1935/2004.

DISPOSAL

In compliance with European directive 2002/96/EC, the appliance must not be disposed of with hou- sehold waste, but taken to an authorised waste se- paration and recycling centre.

19