ENGLISH
7 | Select “Yes”. |
| |
| TUNING |
BAND | MODE |
When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level adjustment mode.
After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each surround mode on page 27.
8 | a. If the “Auto” mode is selected: |
Test tones are automatically emitted from the different | |
| speakers. |
| The test tones are emitted from the different speakers in |
| the following order, at |
| second time around, |
| around and on: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Flashing | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1spkr |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SB |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FL |
|
| C |
|
| FR |
|
| SR |
|
| SBR |
|
| SBL |
|
| SL |
|
| SW |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2spkrs |
|
|
|
|
|
|
|
| ||
Example: When the volume is set to
You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO MOVIE, and MATRIX.
When using either surround speakers A or B, or when using surround speakers A and B at the same time, be sure to adjust the balance of playback levels between each channel for the various selections of “A or B” and “A and B”.
Setting the Digital In Assignment
•This setting assigns the digital input jacks of the
TUNING
BANDMODE
TUNING
TUNING
BANDMODE
TUNING
When the surround back speaker setting is set to “1spkr” for “Speaker Configuration”, this is set to “SB”.
Use the CURSOR buttons to adjust all the speakers to the same volume.
The volume can be adjusted between
b. When the “Manual” mode is selected
Use the CURSOR left and right to select the speaker for which you want to output test tones, then use the CURSOR up and down to adjust so that the volume of the test tones from the various speakers is the same.
Flashing
1 | TUNING | At the System Setup Menu select “Digital In Assignment”. |
| BAND | MODE |
| TUNING |
|
2 | ENTER | Switch to the Digital In Assignment screen. |
SHIFT |
|
TUNING
BAND | MODE | Example: When the volume is set to |
|
| |
| TUNING | subwoofer is selected |
|
|
9 | ENTER | After the above settings are completed, press the ENTER button. |
SHIFT | The “Channel Level” screen reappears. |
To cancel the settings, select “Level Clear” and “Yes” on the “Channel Level” screen, then make the settings again.
The level of each channel should be adjusted to 75 dB
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural balance.
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control.
3 | TUNING |
|
| Select the digital input jack to be assigned to the input source. |
|
| TUNING | • To select the input source | |
| BAND | BAND | MODE | • To select the digital input jack |
| MODE |
|
| |
| TUNING |
| TUNING | Select “OFF” for input sources for which no digital input jacks are used. |
|
|
|
| If “Yes” is selected for “Default”, the settings are automatically reset |
|
|
|
| to the default values. |
4 | ENTER | Enter the setting. | ||
SHIFT | The System Setup Menu reappears. | |||
NOTES:
•The OPTICAL 3 jacks on the
•Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the
•“PHONO” and “TUNER” cannot be selected on the Digital In Assignment screen.
14