Denon AVR-2802 manual 15

8REMOTE CONTROL UNIT

•The included remote control unit (RC-904) can be used to operate not only the AVR-2802 but other remote control compatible DENON components as well. In addition, the memory contains the control signals for other remote control units, so it can be used to operate non-Denon remote control compatible products.

Operating DENON audio components

•Turn on the power of the different components before operating them.

AUDIO Set mode switch 1 to “AUDIO (AVR/AVC)”.

ENGLISH

Inserting the batteries

qRemove the remote control unit’s rear cover.

wSet three R6P/AA batteries in the battery compartment in the indicated direction.

Notes on Batteries

• Use R6P/AA batteries in the remote control unit.
• The batteries should be replaced with new ones
	approximately once a year, though this depends on the
	frequency of usage.
•	Even if less than a year has passed, replace the batteries
	with new ones if the set does not operate even when the
	remote control unit is operated nearby the set. (The
	included battery is only for verifying operation. Replace it
	with a new battery as soon as possible.)
•	When inserting the batteries, be sure to do so in the
	proper direction, following the “≈” and “√” marks in the
	battery compartment.
• To prevent damage or leakage of battery fluid:
	• Do not use a new battery together with an old one.
	• Do not use two different types of batteries.

1
		AVR/AVC			VIDEO
2		TAPE	CDR/MD				Set mode switch 2 to the position for the
	CD					MULTI	component to be operated.
		DVD				TV
		VDP		VCR

		START	LEARNED/TX		RC-904
	SYSTEM CALL			POWER
	SET	CALL	OFF		/
	DVD	VDP		TUNER	SHIFT
	1	2		3
	TV/DBS			PHONO
	4	5		6
	VCR-1	CD		CDR / TAPE	CHANNEL
	7	8		9
	VCR-2/V.AUX				TV/VCR
	+10	0			A / B
						3
	VOLUME				DISC SKIP+
		DOLBY / DTS
	SPEAKER	SURROUND		DIRECT
	DSP SIMULATION	5CH / 6CH STEREO		STEREO
					MASTER VOL.
	INPUT MODE	ANALOG		EXT.IN
1	AUDIO		TAPE	CDR/MD
		CD		MULTI	MUTING
	AVR/AVC	VIDEO DVD		TV		2
			VDP	VCR
			SYSTEM		SURROUND
	TUNING		SETUP		PARAMETER
	BAND	RDS	TITLE		MENU/GUIDE
3				CH SELECT
	MODE	PTY		ENTER
				SELECT
	MEMORY	RT	STATUS		ON SCREEN
		DISPLAY			RETURN
	USE/LEARN	T.TONE	MULTI		DVD
					SET UP

ePut the rear cover back on.

	• Do not short-circuit, disassemble, heat or dispose of
	batteries in flames.
•	Remove the batteries from the remote control unit when
	you do not plan to use it for an extended period of time.
•	If the battery fluid should leak, carefully wipe the fluid off
	the inside of the battery compartment and insert new
	batteries.
• When replacing the batteries, have the new batteries
	ready and insert them as quickly as possible.
•	The learned remote control signals may be cleared if no
	batteries are in the remote control unit for about 5
	seconds.
	The factory-installed codes are in permanent memory,
	however.

3	Operate the audio component.
	• For details, refer to the component’s operating instructions.
	While this remote control is compatible with a wide range of infrared controlled components, some
	models of components may not be operated with this remote control.
	1. CD player (CD) and CD recorder and			2. Tape deck (TAPE) system buttons
	MD recorder (CDR/MD) system buttons
		VCR-2/V.AUX	TV/VCR	VCR-2/V.AUX	TV/VCR
		+10	A / B	+10	A / B
		VOLUME	DISC SKIP+	VOLUME	DISC SKIP+
	6, 7 : Manual search (forward and reverse)			6 : Rewind
	2	: Stop		7 : Fast-forward
	1	: Play		2 : Stop

Using the remote control unit

•	Point the remote control unit at the remote sensor on the
	main unit as shown on the diagram.
•	The remote control unit can be used from a straight
	distance of approximately 7 meters from the main unit,

8, 9 :		Auto search (cue)	1 :		Forward play
3	:	Pause	3	:	Pause
DISC	:	Switch disc	8 :		Reverse play
SKIP +		(for CD changers only)	A/B	:	Switch between decks A and B

30° 30°

Approx. 7 m

but this distance will be shorter if there are obstacles in

the way or if the remote control unit is not pointed directly

at the remote sensor.

• The remote control unit can be operated at a horizontal

angle of up to 30 degrees with respect to the remote

sensor.

NOTES:

•It may be difficult to operate the remote control unit if the remote sensor is exposed to direct sunlight or strong artificial light.

•Do not press buttons on the main unit and remote control unit simultaneously. Doing so may result in malfunction.

•Neon signs or other devices emitting pulse-type noise nearby may result in malfunction, so keep the set as far away from such devices as possible.

3. Tuner system buttons

SYSTEM CALL		POWER
SET	CALL	OFF	ON / SOURCE
DVD	VDP	TUNER	SHIFT
1	2	3
TV/DBS		PHONO
4	5	6
VCR-1	CD	CDR / TAPE	CHANNEL
7	8	9

SHIFT	: Switch preset channel range
CHANNEL	: Preset channel up/down
+, –

*For the tuner only, the following buttons can also be operated:

		SYSTEM	SURROUND
TUNING		SETUP	PARAMETER
BAND	RDS	TITLE	MENU/GUIDE
			CH SELECT
MODE	PTY		ENTER
			SELECT
MEMORY	RT	STATUS	ON SCREEN
		DISPLAY	RETURN

TUNING •, ª	: Tuning up/down
BAND	: Switch between AM and FM bands
MODE	: Switch between auto and mono
MEMORY	: Preset memory
SHIFT	: Switch preset channel range
RDS	: RDS search
PTY	: PTY search
RT	: Radio text

15