ENGLISH
Getting | Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup) | ||
NOTE |
| ||
a Connect the Included Setup | |||
Started | • Loud test sounds may be played during Audyssey MultEQ® | ||
automatic speaker setup. This is part of normal operation. If there | Microphone | ||
2Press o p to select Amp Assign Mode, then press
RETURN.
| is background noise in room, these test signals will increase in | vpage 29 of GThe original versionH Operating Instructions | |||||||
Connections | volume. |
|
|
|
|
|
|
|
|
• Do not stand between the speakers and setup microphone or allow |
|
|
|
|
|
|
|
| |
obstacles in the path while the measurements are being made. This |
|
|
|
|
|
|
|
| |
will cause inaccurate readings. | s Audyssey Auto Setup Preparations |
|
| ||||||
• Make the room as quiet as possible. Background noise can disrupt |
|
| |||||||
Settings | the room measurements. Close windows, silence cell phones, |
|
|
|
|
| around items indicate the default setting. |
|
|
televisions, radios, air conditioners, fluorescent lights, home |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ||
appliances, light dimmers, or other devices as measurements may |
|
|
|
|
|
|
|
| |
STEP1 Preparation |
| ||||||||
be affected by these sounds. |
| ||||||||
|
| ||||||||
Playback |
|
|
|
|
|
|
|
| |
Cell phones should be placed away from all audio electronics during | Perform the following settings if adjustments, etc., are required for | ||||||||
the measurement process as Radio Frequency Interference (RFI) | the speaker environment you’re using. | ||||||||
may cause measurement disruptions (even if the cell phone is not in | If you do not need to perform the following settings, or have already | ||||||||
| use). | completed | them, select “Auto Setup Start” and then press ENTER. | ||||||
|
|
| |||||||
Normal
ZONE2
ZONE3
Front A
Front B
Front Height
:The surround back channel audio signals are output.
:The ZONE2 audio signals are output.
:The ZONE3 audio signals are output.
:The ZONE2 / ZONE3 monaural audio signals are output.
:The
:The
:The front height channel audio signals are output.
Information | • Operating MASTER VOLUME during the measurements will cancel | Proceed to “ STEP2 ”. | |||
|
|
|
| ||
the measurements. | Change the Amplifier Assignment (Amp Assign) | ||||
| |||||
| The signal output from the SURR.BACK/AMP ASSIGN speaker | ||||
Unavailable |
| ||||
| terminal of the | ||||
| environment (vpage 8 “Amp Assign”). | ||||
|
|
| |||
| 1 | Press ui to select | |||
Upgrading After Functions |
| “Amp Assign”, then | |||
|
| press ENTER. | |||
|
|
|
|
| |
|
|
|
|
| |
Specifications |
|
|
|
|
|
Front Wide : The front wide channel audio signals are output.
indicates functions added by upgrading.
•When you are using surround back speakers with ZONE2/ZONE3, set to “ZONE2” or “ZONE3”.
•You can set in the same way as described in “Amp Assign” on page 8.
NOTE
Since “Amp Assign” of
Set the channel to be measured (Channel Select)
vpage 30 of GThe original versionH Operating Instructions
d Perform Audyssey Auto Setup
vpage 30 of GThe original versionH Operating Instructions
Main remote control | :Displaying the menu | :Moves the cursor | :Confirm the setting | :Return to previous menu | |
| operation buttons | Cancel the menu | (Up/Down/Left/Right) |
|
|