ENGLISH
Getting |
| A2Crossover Frequency |
|
|
|
|
|
|
|
|
|
| |||||||||||
| Select crossover frequency from which subwoofer handles low |
|
| ||||||||||||||||||||
Started |
| range signal. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| [Display] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
Connections |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 1 | .Sp 2.In 3.Op |
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Q |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Speaker | Setup |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Q |
|
|
|
|
|
Setup |
|
|
|
|
|
|
|
|
|
| 12Cr.Over | 80Hz |
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| [Selectable items] |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
Playback |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 40Hz |
| 60Hz |
| 80Hz |
| 90Hz |
| 100Hz |
| 110Hz |
| 120Hz |
| 150Hz |
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||||
Remote |
| 200Hz |
| 250Hz | : |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Only the portion of the bass sound of the various speakers output | ||||||||||||||||||||||
|
| ||||||||||||||||||||||
|
| from the subwoofer that has a frequency below the frequency set | |||||||||||||||||||||
Control |
| here is output. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| speakers you are using. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
| Set this according to the low frequency reproduction capabilities of the | |||||||||||||||||||||
Information |
| • The “Crossover Frequency” can be set when there are speakers that | |||||||||||||||||||||
|
| ||||||||||||||||||||||
|
| have been set to “Small” at “System Setup” – “Speaker Setup” or | |||||||||||||||||||||
Troubleshooting |
| when “Subwoofer” is set to “Yes” (vpage 20). |
|
|
|
|
|
|
| ||||||||||||||
| speakers, however, we recommend setting the crossover frequency | ||||||||||||||||||||||
|
| • For speakers set to “Small”, sound below the crossover frequency | |||||||||||||||||||||
|
| is cut from the sound output. The cut bass sound is output from the | |||||||||||||||||||||
|
| subwoofer or front speakers. |
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
| • Always set the crossover frequency to “80Hz”. When using small | |||||||||||||||||||||
|
| to a higher frequency. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
A3Test Tone
Adjust channel levels to obtain equal volume from all speakers.
[Display]
1.Sp 2.In 3.Op
Q
Speaker Setup
Q
13 T.Tone Yes<
Q
T.Tone Auto >
Q
Test Tone On
Q
Auto-FL
Test Tone
Select test tone playback method.
[Selectable items]
Auto : Automatically switch speaker from which test tone is output.
Manual : Manually switch speaker from which test tone is output.
Test Tone Start
Press the obutton to select “Yes”, then press the o pbutton to select “Auto” or “Manual”.
Then press the ibutton. Out put the test tone.
Auto : Press the o pbutton to adjust the volume.
Manual : Press the u ibutton to select the speaker, then press the o pbutton to adjust the volume.
When the adjustments are completed, press the ENTER button to finish the test tone.
[Variable range] –12dB ~ 0dB ~ +12dB
Operating from the remote control unit
Adjusting with the remote control unit using the test tones is only possible in the “Auto” mode and only effective in the STANDARD mode. The adjusted levels for the different modes are automatically stored in the memory.
GAdjusting using test tonesH
qPress the TEST button.
Test tones are output from the various speakers.
w Use the o p button to adjust so that the volume is equal for all speakers.
e When the adjustments are completed, press the TEST button again.
•Speakers set to “None” in the Speaker Configuration settings are not displayed.
•When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 35.