ENGLISH
!7Input select switch
•Switches between the PHONO/LINE and LINE inputs.
•When the lever of switch is vertical position, the LINE2 or LINE4 input is selected.
•When the lever of switch is slope, the PHONO1/LINE1 or PHONO2/lINE3 input is selected.
•You can perform 8 direction placement. See page 10.
!8SPLIT CUE button
•In the STEREO mode, the stereo sound of MASTER and CUE are fed to both ear cups. In the SPLIT CUE mode, the headphone circuit provides monaural CUE sound to the left and monaural MASTER sound to the right.
•When the Level Meter mode select switch is set to “MASTER”…In the STEREO mode, the meter indicates the stereo level in the L/R Master output. In the SPLIT CUE mode, the monaural CUE sound level is displayed on the left and the monaural MASTER sound level is displayed on the right.
•In the SPLIT CUE mode, the LED is lit.
!9PGM 1/2 KILLS switches
•These switches are used cut out the Treble, Mid or Bass frequencies of the incoming audio signal. When these switches moved up or down, the selected frequency level is cut, the LED located directly above the specific switch will glow indicating the cut function has been activated.
@0Level meter mode select switch
•The position of this switch will determine the Level Meter mode. In the “MASTER” position, the meter will detail the out level of the left and right channels. In the “PGM 1/2” position, the left side of the meter will indicate monaural level of the PGM 1 and the right side of the meter will indicate monaural level of the PGM 2.
@1Channel Fader
• Controls the channel output level.
@2Level meter
•The dual LED's indicators are used to detail either the master output level, a combination of the master output level and the CUE signal level, or the PGM1/2 monaural level.
@3Crossfader
•Fades the overall mixer output between channels 1 and 2.
(2) Rear panel
@4Power operation switch (POWER)
• Selects power “ON” or “OFF”.
NOTE:
Whenever the power switch is in the OFF state, the AC adaptor is still connected on AC line voltage. Please be sure to unplug the cord when you don’t use for along time.
@5BALANCED MASTER OUT jacks
•These 1/4” TRS jacks provide a balanced line level output.
•Connect these jacks to the balanced analog input jacks on an amplifier or console.
•Pin layout: Tip=Hot Ring=Cold Sleeve=GND
@6EFFECT LOOP SEND/RETURN jacks
•These 1/4” TS stereo jacks allow external processing of the program signal.
•When connect monaural type effect processor, use Lch input and output.
@7MIC BALANCED INPUT jack
•Accepts an balanced microphone with 1/4” TRS mono jacks.
•Pin layout: Tip=Hot Ring=Cold Sleeve=GND
@8MIC EFFECT LOOP jack
•These 1/4” TRS jack allow external processing of the program signal.
•Pin layout:
Tip=SEND Ring=RETURN Sleeve=GND
@9PGM1, 2 FADER output jacks
•Connect these jacks to the FADER input jacks of
#0Phono ground screw (GND)
•This screws provide a place to connect the ground wire from a turntable.
•This terminal is exclusively for a turntable ground and not a safety earth ground.
#1PHONO1, 2 / LINE1, 3 switches (LN / PH)
•These switches change the input from PHONO to a LINE level input.
•These switches set a LINE level input when turntable is not connected.
NOTE:
Always be sure main power is shut off before change the position of the Line Level Selector Switch.
#2PHONO1, 2 / LINE1, 3 input jacks
•These stereo pairs of unbalanced RCA jacks are inputs for a PHONO (RIAA) stage for magnetic (MM) cartridges or a LINE stage suitable for any device, such as a CD player.
#3LINE2, 4 input jacks
•These stereo pairs of unbalanced RCA jacks are inputs for any line level device.
#4AUX INPUT jacks
•This stereo pair of RCA jacks provides an unbalanced line level input with independent top panel AUX INPUT control.
•This input is mixed after the Crossfader and
EFFECT LOOP.
#5BOOTH OUT jacks
•This stereo pair of RCA jacks is the same as the MASTER output with independent BOOTH LEVEL control.
•This output may be for recording, booth/zone monitoring, or for connecting to another mixer.
#6UNBALANCED MASTER OUT jacks
•This stereo pair of RCA jacks provides an unbalanced line level output.
•Connect these jacks to the unbalanced analog input jacks on an amplifier or console.
#7AC IN
• Input connection for the included AC adaptor.
NOTE:
Use specified attached AC adaptor only.
(3) Front panel
#8CH 1/2 FADER START switches
•Use this to switch the Channel Fader Start function ON and OFF.
#9CROSSFADER START A, B switches
•Use this to switch the Crossader Start function ON and OFF.
$0HEADPHONE output jack
• Accept 1/4” stereo headphone plugs.
$1CH 1/2 FADER CONTOUR adjustment
•Adjusts the curve of the CH1/2 faders between fast, normal , or slow fade.
$2CH 1/2 FADER REVERSE switch
•Reverses the direction of each respective input CH1/2 fader.
$3CROSSFADER CONTOUR adjustment
•Adjusts the shape of the crossfader curve from a fast cut for scratching or to a slow fade for mixing.
$4CROSSFADER REVERSE switch
• Reverses the direction of the crossfader.
6