Denon DN-X800 operating instructions Part Names and Functions, Main Features, Installation

ENGLISH

– TABLE OF CONTENTS –

z Main features	4	b Fader start	7
x Installation	4	n X-effect	8
c Part names and functions	4, 5	m Replacing the crossfader	9
v Connections	6	, Specifications	9

3PART NAMES AND FUNCTIONS

(1)Front Panel

q MIC EQ controls !0 LINE/DIGITAL input select switch

•ACCESSORIES

Please check to make sure the following items are included with the main unit in the carton:

....................................................q Operating instructions 1 ..................w Connection cords (3.5 mm stereo mini cord) 2

•Contour the frequency response of the Main Mic input

-12 dB to +12 dB.

HI

•Adjusts high-tone microphone sound -12 dB to +12 dB.

At the center position, sound is flat.

MID

•Adjusts mid-tone microphone sound -12 dB to +12 dB.

At the center position, sound is flat.

• Selects either a Line (analog) or Digital Input for the

Source.

• The adjacent green indicator flashes when the digital

signal is unlocked and remains lit when the digital

signal is locked.

NOTE:

You must first set the pitch slider to zero % of the

digital output source (CD, MD) before it's power is

1MAIN FEATURES

LOW

•Adjusts low-tone microphone sound -12 dB to +12 dB. At the center position, sound is flat.

turned on. If the green digital indicator is flashing on

the mixer, please perform the above steps.

CONGRATULATIONS! You have purchased the DENON DN-X800 DJ mixer from DENON.

1.X-Effect

The X-Effect is a unique feature which is designed to work with the DENON DN-2100F and DN-2600F CD players. The fader start of the below functions can be used with the Crossfader.

Sampler, Hot start brake/platter, Hot start 1, 2 (each drive).

2.CH. Fader and Crossfader start

The CD player can be started or stopped simply by increasing or decreasing the level of the CH fader or by using the cross fader left to right or right to left. (This function can only be used when the DENON CD players DN-1800F, DN-2100F or DN-2600F is connected to the DN-X800.)

3.Digital outputs

The DN-X800 allows you to record directly to CD-R, MiniDisc or a hard disk device through it’s exclusive coaxial digital outputs.

The digital outputs maintains a constant 16 bit / 44.1 kHz signal.

4.Digital inputs

The DN-X800 accepts up to 4 digital inputs.

Such as our family of performers, DN-1800F, DN-2100F, DN-2600F, DP-DJ151 or any device with a digital output. The sampling frequency range can be 32 kHz, 44.1 kHz or 48 kHz.

5.Enhanced input/output terminals (Analog)

8 Line, 3 Phono, 2 microphone systems, 2 Main outputs, Zone output, Booth output, Sub woofer output and tape output are provided independently. Effect in/out terminals are also provided for a external effects processor.

6.3-Band equalizer/Gain

Bass, Mid, Treble and Gain controls are available on every input channel.

7.Crossfader contour

This feature allows adjusting the “shape” of the Crossfader response from a gentle curve for smooth, long running fades, to the steep pitch required for top performance cut and scratch effects.

8.Mic post

This feature will pass the Main Mic signal into the Zone, Booth, Tape output and Digital output signal path.

In the OFF mode, the MIC signal will not be routed through the above outputs.

wMAIN MIC level control

• Adjusts the level of the Main Mic input.

eMAIN MIC ON/OFF button

•Puts the Main Mic signal into the Main outputs signal path.

•When the button is pressed, the Main Mic is on and the adjacent orange indicator lights.

rMIC POST ON/OFF button

•Puts the Main Mic signal into the Zone, Booth Tape and Digital out signal path.

•When the button is pressed, the adjacent green indicator lights.

tAUX MIC level control

• Adjusts the level of the Aux Mic input.

yAUX MIC ON/OFF button

•Puts the Aux Mic signal into the mixer signal path.

•When the button is pressed, the Aux Mic is on and the adjacent orange indicator lights.

uSource EQ controls

•Contour the frequency response of the selected inputs.

HI

•Adjusts the high-tone sound -26 dB to +10 dB.

At the center position, sound is flat.

MID

•Adjusts the mid-tone sound -26 dB to +10 dB. At the center position, sound is flat.

LOW

!1 Source input fader (Ch. fader)

•Controls the level of the selected Input.

!2 ZONE level control

•Adjusts the level of the Zone outputs.

!3 ZONE METER button

•When this button is pressed down and held, the meter indicates the stereo level in the LEFT and RIGHT meter output. The adjacent green indicator lights.

!4 BOOTH LEVEL control

•Adjusts the level of the Booth outputs.

!5 MASTER LEVEL fader

•Adjusts the level of the Main outputs. Signals from the channels selected with the Assign switches will be output using the Source input fader (Ch. fader) and the Crossfader, while signals from other channels will be outputs using the Source input fader (Ch. fader).

!6 Peak dB CUE/PROGRAM meter

•Displays the output level following Master Level adjustment, the peak level is held for 1 second. Display range : -20 dB to +8 dB.

•Can switch between two display mode. See below

@3.

!7 SUBWOOFER frequency control

•Adjusts the cut off frequency of the low pass filter 40 Hz to 200 Hz.

•The low adjustment, will effect the Subwoofer output.

!8 EFFECT LOOP MAIN button

2INSTALLATION

When the DN-X800 is mounted inside a coffin or DJ booth, we recommend leaving a 3 cm blank space above the mixer if

possible. cm3

Min.

MIC 1 2 3 4

ZONE MASTER SUB WOOFER

EFFECT LOOP

BOOTH

DIGITAL

CROSSFADER

CONTOUR

A B

PHONES DJ MIXER

•Adjusts the low-tone sound -26 dB to +10 dB. At the center position, sound is flat.

NOTE:

Clipping may occur if adjustments are set to harsh.

iGAIN level control

•Adjusts the level of the selected input 0 to +10 dB.

oSource input select switch

•Selects either a Phono/Line or Line input for the source.

•Routes the Main signal through the external processor attached to the EFFECT connectors on the rear.

•When the button is pressed in, the adjacent orange indicator lights. (When the processor isn't attached,indicator blinks.)

!9 EFFECT LOOP MIC button

•Routes the Main Mic signal through the external processor attached to the EFFECT connectors on the rear.

•When the button is pressed in, the adjacent orange indicator lights. (When the processor isn't attached,indicator blinks.)

NOTE:

When the Effect Loop Main and Mic are on, the signal of Mic is output to all the outputs regardless of setting the Main Mic and the Post Mic.

4