7REPLACING THE CROSSFADER
The Crossfader may be removed without any disassembly of the
1.Remove the two (2) outer screws attaching the crossfader assembly to the front panel.
2.Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.
3.Install the replacement assembly by reversing the above instructions.
ENGLISH
8SPECIFICATIONS
■GENERAL
Dimensions: | 482 | (W) x 105 (H) x 177 (D) mm (without feet) | |||
Installation: |
|
| |||
Mass: | 5.5 kg |
|
|
| |
Power supply: | 230 | V AC | ±10%, 50 Hz | (Europe model) | |
| 220 | V AC | ±10%, 50 Hz | (China model) |
|
Power consumption: | 26 W |
|
|
| |
Environmental conditions: | Operational temperature: | 5 to 35°C | (41 to 95°F) | ||
| Operational humidity: | 25 to 85% | (no condensation) | ||
| Storage temperature: | (4 to 140°F) |
■AUDIO SECTION
Input Sensitivity & Impedance:
Main Mic | (2.0 mV) | 10 kΩ | /kohms | ||
Aux Mic | (1.0 mV) | 10 kΩ | /kohms | ||
Effect (Return) | (200 mV) | 50 kΩ | /kohms | ||
(3.0 mV) | 50 kΩ | /kohms | |||
(200 mV) | 50 kΩ | /kohms | |||
Output level & Impedance: |
|
|
|
|
|
Main (Balanced) | 4 dBm | (1.23 V) | 600 Ω | /ohms load | |
Main (Unbalanced) | 0 dBV | (1.0V) | 1 kΩ | /kohms | |
Zone (Balanced) | 4 dBm | (1.23 V) | 600 Ω | /ohms load | |
Booth (RCA) | 6 dBV | (2.0 V) | 1 kΩ | /kohms | |
Tape (RCA) | (316 mV) | 1 kΩ | /kohms | ||
Effect (Send) | (200 mV) | 1 kΩ | /kohms | ||
Subwoofer | (800 mV) | 1 kΩ | /kohms | ||
Headphone | (630 mV) | 150 Ω | /ohms |
Frequency Response: |
|
|
Line | 20 to 20 kHz | ±2 dB |
Phono | 20 to 20 kHz | RIAA ±2 dB |
Mic | 20 to 20 kHz | ±2 dB |
Signal to Noise ratio: |
|
|
Line | 80 dB | 0 dBm, 1 kHz, EQ flat |
Phono | 75 dB | 0 dBm, 1 kHz, EQ flat |
Main Mic | 65 dB | 0 dBm, 1 kHz, EQ flat |
Total harmonic distortion rate: |
|
|
Line | Below 0.05% |
|
Phono | Below 0.05% |
|
Cross talk: | Over 70 dB |
|
Channel equalizer: |
|
|
Hi | +10 dB, | |
Mid | +10 dB, | |
Low | +10 dB, | |
Microphone equalizer: |
|
|
Hi | +12 dB, | |
Mid | +12 dB, | |
Low | +12 dB, | |
Digital input: |
|
|
Input sensitivity | ||
Signal format | SPDIF |
|
Output level | 0.5 | /ohms |
Digital output: |
|
|
Signal format | IEC958 Type II | |
Output level | 0.5 | /ohms |
Output signal level |
|
✽Specifications and design are subject to change without notice for purpose of improvement.
9