Denon DRA-F101 9USING THE TIMER, (3) Setting the Timer, (2) Before Setting the Timer, (1) Setting the Current Time (12-hourdisplay), 2 3,5,7 4,6, 2 3, 5, 7, 9,11,13,15,17

9USING THE TIMER

(1) Setting the Current Time (12-hour display)

Example: Setting the current time to 9:30 p.m.

2 3,5,7 4,6

VOLUME

FUNCTION				MEMORY	TUNING			SOURCE
	TONE	TIMER	DISPLAY	/ SET	DOWN	UP	BAND	DIRECT

SYSTEM

ON / STANDBY

PHONES

Use the TUNING buttons	TUNING
	DOWN	UP
to input the hours (PM 9).
• “9” flashes in the hours
position.

4

Press the MEMORY/SET button.	MEMORY
	/ SET

•“9” stops flashing, remaining lit,

(3) Setting the Timer

2The timer function lets you switch the power between the on and standby modes automatically at the desired times.

2When connected in a system with the DCD-F101, the timer can be used to play a CD.

Example: Using the everyday timer to listen to the station stored at preset number 3 (FM 98.00 MHz) from 2:35 p.m. to 2:56 p.m.

2 3, 5, 7, 9,11,13,15,17

ENGLISH

TUNING

Use the TUNING buttons	DOWN	UP
to switch the function to
“TUNER”.

5
	✽ The function switches as follows each time
		the button is pressed:

AM-FM STEREO RECEIVER DRA-F101

1

5

and the minutes position starts flashing.

VOLUME

FUNCTION				MEMORY	TUNING			SOURCE
	TONE	TIMER	DISPLAY	/ SET	DOWN	UP	BAND	DIRECT
SYSTEM
ON / STANDBY
PHONES

AM-FM STEREO RECEIVER DRA-F101

: When the TUNING UP button is pressed.

	SYSTEM
	ON / STANDBY
1	Turn on the power.
	TIMER
	Press the TIMER button for at least
	3 seconds.
	• “TIME” flashes on the display.
2	✽ If the time is already set,
	“EVERYDAY” is displayed.
	Press one of the TUNING buttons
	to display “TIME”, then perform
	step 3.
	MEMORY
	/ SET
	Press the MEMORY/SET button.
	• The hours position flashes.
3

	Use the TUNING buttons to	TUNING
		DOWN	UP
	input the minutes (30).
	• “30” flashes in the
6	minutes position.

	Press the MEMORY/SET button
	at the sound of the chime of a	MEMORY
	time service, etc.	/ SET
	• “30” stops flashing, remaining
7	lit, and the current time is
	displayed.

✽The number changes continuously when one of the tuning buttons (TUNING UP or DOWN) is pressed.

✽If the time is already set when step 2, 3 is performed, both the hours and minutes positions flash.

1,18 4, 6, 8,10,12,14,16

SYSTEM

ON / STANDBY

1 Turn on the power.

TIMER

Press the TIMER button for at least 3 seconds.

2	• “EVERYDAY” is displayed.
	✽ If the time is not set, “TIME” is displayed.
	Perform steps 3 to 7 on page 15, then start
	the timer setting over.
		TUNING
	Press one of the TUNING	DOWN	UP
3 buttons to display
	“EVERYDAY” or “ONCE”.

: When the TUNING DOWN button is pressed.

Press the MEMORY/SET button.	MEMORY
	/ SET
6 • “TUNER” is stored in the
memory as the timer function.
TUNING
DOWN	UP
Use the TUNING buttons
to set preset number 3.

7

	Press the MEMORY/SET	MEMORY
	button.	/ SET
	• The preset station is stored in
	the memory and the timer on
	time setting mode is set.
8	“E” and “oN” appear
	alternately in the display in the

(2) Before Setting the Timer

2 Be sure to set the current time. If the current time is not set, the timer standby indicator (“ ”) will not light and the timer will not function.

Press the MEMORY/SET button.	MEMORY
	/ SET
• This sets the unit to the timer
setting mode’s function

steps 8 to 11.

2Be sure to preset the station before setting the timer. (Refer to “Presetting AM and FM stations” on page 14.)

2The DRA-F101 is equipped with two types of timers: the everyday time which turns the power on and off at the same times every day, and the once timer that turns the power on and off only once.

2Do not change the timer standby mode after the timer is activated (after the timer on time is reached). The timer may not operate properly.

2It is not possible to set the timer start and end times to the same time.

2If the display or operation is not normal, unplug the power cord, then plug it back in while pressing the memory/set button (MEMORY/SET). This restores the tuner to the initial default values. After doing this, reset the presettings, current time and timer settings.

2When setting the timer to operate the CD player do so with a disc loaded and the disc holder closed. The timer will not operate properly if no disc is loaded or if the disc holder is open.

setting mode.

4 Example: When the everyday timer is

selected

9

<Setting the timer on		TUNING
time>	DOWN		UP

Use the tuning buttons to set the hours position to “PM 2”.

15