6TRACK MARK

•CD category digital signals are output from the DN-X400’s digital outputs. Track numbers can be added at any position during recording of these signals onto a digital recorder.

•Connect the DN-X400’s digital outputs to the digital recorder. (Refer to v CONNECTIONS on page 7.)

ENGLISH

9SPECIFICATIONS

■GENERAL

Dimensions:

482

(W) x 105 (H) x 177 (D) mm (without feet)

Installation:

19-inch rack mountable 4U

Mass:

5.5 kg

Power supply:

120

V AC ±10%, 60 Hz (U. S. A. and Canada models)

1

Start recording on the digital recorder.

Press the TRACK MARK button.

•The output signal’s track number changes and the green indicator lights for 4 seconds.

2

TRACK

 

MARK

lit

NOTE:

During the 4 seconds in which the track number is being changed, the track number cannot be changed again.

 

230 V AC

±10%, 50 Hz (European models)

Power consumption:

26 W

 

 

 

 

Environmental conditions:

Operational temperature:

5 to 35°C

(41 to 95°F)

 

Operational humidity:

25 to 85% (no condensation)

 

Storage temperature:

-20 to 60°C

(4 to 140°F)

■ AUDIO SECTION

 

 

 

 

 

Input Sensitivity & Impedance:

 

 

 

 

 

Main Mic

-54 dBV

(2.0 mV)

10 kΩ

/kohms

 

Aux Mic

-60 dBV

(1.0 mV)

10 kΩ

/kohms

 

Effect (Return)

-10 dBV

(316 mV)

50 kΩ

/kohms

 

2-Phono

-50 dBV

(3.0 mV)

50 kΩ

/kohms

 

8-Line

-14 dBV

(200 mV)

50 kΩ

/kohms

 

7PFL (Pre Fader Level)

1.Press the HEADPHONE mode button.

2.Press the CUE button that you wish to monitor 1~4 (make sure your source is playing).

3.Turn the blue GAIN level knob until the L/CUE (top) meters peak at the 0 dB level.

4.Perform your mix using the cross fader or channel fader at your desire.

NOTES:

•For proper operation, your channel levels should always be set to or left on reference line 8.

•This adjustment can be made even if the channel fader is set to zero level.

8REPLACING THE CROSSFADER

The Crossfader may be removed without any disassembly of the DN-X400 itself.

1.Remove the two A outer screws attaching the crossfader assembly to the front panel.

2.Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.

3.Install the replacement assembly by reversing the above instructions.

A

A

Output level & Impedance:

 

 

 

 

 

Main (Balanced)

4 dBm

(1.23 V)

600 Ω /ohms load

Main (Unbalanced)

0 dBV

(1.0V)

1 kΩ

/kohms

Booth/Zone (Balanced)

4 dBm

(1.23 V)

600 Ω /ohms load

Rec (RCA)

-10 dBV

(316 mV)

1 kΩ

/kohms

Effect (Send)

-10 dBV

(316 mV)

1 kΩ

/kohms

Subwoofer

-2 dBV

(800 mV)

1 kΩ

/kohms

Headphone

-4 dBV

(631 mV)

150 Ω /ohms (33 Ω /ohms load)

Frequency Response:

 

 

 

 

 

Line

20 to 20 kHz

±2 dB

 

 

Phono

20 to 20 kHz

RIAA ±2 dB

 

Mic

20 to 20 kHz

±2 dB

 

 

Signal to Noise ratio:

 

 

 

 

 

Line

80 dB

 

0 dBm, 1 kHz, EQ flat

Phono

75 dB

 

0 dBm, 1 kHz, EQ flat

Main Mic

65 dB

 

0 dBm, 1 kHz, EQ flat

Total harmonic distortion rate:

 

 

 

 

 

Line

Below 0.05%

 

 

 

Phono

Below 0.05%

 

 

 

Cross talk:

Over 70 dB

 

 

 

Channel equalizer:

 

 

 

 

 

Hi

+10 dB, -26 dB (13 kHz)

 

 

Mid

+10 dB, -26 dB (1 kHz)

 

 

Low

+10 dB, -26 dB (70 Hz)

 

 

Microphone equalizer:

 

 

 

 

 

Hi

+12 dB, -12 dB (10 kHz)

 

 

Mid

+12 dB, -12 dB (1 kHz)

 

 

Low

+12 dB, -12 dB (100 Hz)

 

 

Digital output (COAXIAL):

 

 

 

 

 

Signal format

IEC958 Type II

 

 

Output level

0.5 Vp-p 75 Ω

/ohms

 

 

Output signal level

-6 dB

 

 

 

 

Digital output (OPTICAL):

 

 

 

 

 

Signal format

IEC958 Type II

 

 

✽Specifications and design are subject to change without notice for purpose of improvement.

9