![](/images/new-backgrounds/1009673/967353x1.webp)
OWNER’S MANUAL
OPERATING
FIREPLACE
Continued
1. After lighting, let pilot flame burn for |
about one minute. Turn gas control |
knob on the control valve to ON po- |
sition. Turn variable control knob |
anywhere between HI and LO. Slide |
the selector switch to the REMOTE |
position. Note: The burner(s) may |
light if |
was on when selector switch was last |
turned off. You can now turn the |
burner(s) on and off with either op- |
tional |
IMPORTANT: Do not leave the se- |
lector switch in the REMOTE posi- |
tion when the pilot is not lit. This will |
drain the battery. |
IMPORTANT: Be sure to press the |
ON/OFF buttons on the |
remote control unit for up to 3 sec- |
IMPORTANT: The
3.Use the STATUS button on the hand- held remote control unit to see the operation mode being used and the temperature setting selected. A red light will come on beside the opera- tion mode being used.
4.To turn the burner(s) off when oper- ating in the manual mode, press the OFF button. If operating in the auto mode, press the MAN button, then press the OFF button. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the gas con- trol knob on the heater to the OFF position or set selector switch to OFF position.
Blower Control Knob Variable
OPERATING
OPTIONAL BLOWER
ACCESSORY
Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the left just inside the louver panel.
Both the GA3700 manual blower and the DA3610T
Note for DA3610T Only: If you are using DA3610T blower with optional ther- mostat (wall mount or remote control) for the fireplace, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot
onds to assure proper operation. |
GHRC Series Operation:
2a. Press the ON/OFF button to turn the
(Optional Accessory)
OFF
ON
Control Knob
position, the blower will continue to run. The blower will shut off after the firebox temperature decreases.
The blower helps distribute heated air
burner(s) on and off. When turning burner(s) off, the pilot will remain lit.
GHRCT Series Operation:
2b. Select the MAN (manual) or AUTO button on the
• In manual mode, turn burner(s) on |
or off by pressing the ON or OFF |
buttons on the |
control unit. |
|
| N |
| L |
|
|
| O |
| O | I |
ON OFF REMOTE | T | F | O | H | |
O |
|
| |||
|
| F |
|
| |
|
| LIP |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gas Control
Control Selector Switch in Knob in On
Remote Position (Optional Position
Remote Control)
Figure 58 - Setting the Selector Switch, Gas Control Knob, and Variable Control Knob for Remote Operation
from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions that will hinder the flow of air.
• In auto mode, the room tempera- |
ture is controlled by the thermo- |
stat in the |
trol unit. To increase the room tem- |
perature, press the top arrow of the |
TEMP button. To lower the room |
temperature, press the bottom ar- |
row of the TEMP button. At higher |
settings the heater will run more. |
IMPORTANT: This remote control |
has been specially engineered to |
take an air temperature sample |
Shows Temperature Setting
Allows Burners to be Turned On and Off with the
The Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected.
HI
TEMP
MAN LO ON
AUTO OFF
STATUS
Increases Room Temperature
Decreases Room Temperature
Turns Burners On and Off
Shows Current Operation Mode
every 5.5 minutes in the auto mode. |
It will not respond immediately to |
the temperature setting being |
turned up or down. |
Figure 59 - Hand-Held Thermostat Remote Control Unit Selections (GHRCT Only)
Continued
104558 | 27 |