OWNER’S MANUAL
PRE-INSTALLATION
PREPARATION
Continued
13" | 9 1/4" | 41" |
29"
12 5/8"
34 3/8"
GENERAL VENTING
These models are approved for use with Simpson
Your fireplace is approved to be vented either through the side wall, or vertically using the following guidelines:
• Only use Comfort Glow or Simpson Dura- Vent GS venting components or kits spe- cifically approved for this fireplace.
• Minimum clearance between vent pipes and combustible materials is 1" (25 mm), except where stated otherwise.
• Combustible material may be flush with the top front of fireplace with a maxi-
35 1/16"
Nailing Tabs
mum thickness of 3/4".
58"
Figure 6 - Framing Clearances for Corner Installation
•Do not recess venting terminals into a wall or siding.
•Install horizontal venting with a 1/4" rise for every 12" of run toward the termination.
•You may paint the vent terminal with 450ºF (232ºC)
|
|
|
|
|
|
|
|
|
|
| 1 |
Note: There must be |
|
|
|
|
|
| 2 | ||||
|
|
|
|
|
|
| |||||
a minimum clear- |
|
|
|
|
|
| 3 | ||||
ance of 18" above | A |
|
|
| |||||||
top of louver |
|
|
|
|
|
| 4 | ||||
opening when |
|
|
|
|
|
| |||||
|
|
|
|
|
|
| |||||
installing a television |
| B |
|
| 5 | ||||||
or entertainment |
|
|
|
| C |
| |||||
center above the |
|
|
|
| 6 | ||||||
|
|
|
|
|
| ||||||
fireplace. |
|
|
|
|
|
|
| D |
| ||
|
|
|
|
|
|
|
|
|
| E | 7 |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| F | G |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| Top of Louver Opening | |
|
|
|
|
|
|
|
|
| |||
| Ref. |
| Mantel Depth |
| Ref. |
| Mantel from Top |
| |||
|
|
|
|
|
|
|
|
| of Louver Opening |
| |
|
|
|
|
|
|
|
|
| |||
| 1 |
| 14" (356mm) |
| A |
| 16" (406mm) |
| |||
|
|
|
|
|
|
|
|
| |||
| 2 |
| 12" (305mm) |
| B |
| 14" (356mm) |
| |||
| 3 |
| 10" (254mm) |
| C |
| 12" (305mm) |
| |||
|
|
|
|
|
|
|
|
| |||
| 4 |
| 8" (203mm) |
| D |
| 10" (254mm) |
| |||
|
|
|
|
|
|
|
|
| |||
| 5 |
| 6" (152mm) |
| E |
| 8" (203mm) |
| |||
|
|
|
|
|
|
|
|
| |||
| 6 |
| 4" (101mm) |
| F |
| 6" (152mm) |
| |||
|
|
|
|
|
|
|
|
| |||
| 7 |
| 2" (51mm) |
| G |
| 4" (101mm) |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Figure 7 - Clearances for Combustible Mantels
• There must not be any obstruction such as bushes, garden sheds, fences, decks, or utility buildings within 24" from the front of the termination cap.
• Do not locate termination cap where ex-
Wall
cessive snow or ice build up may occur. Be sure to clear vent termination area af- ter snow falls to prevent accidental block- age of venting system. When using snow blowers, do not direct snow towards vent termination area.
LOCATION OF VENT
TERMINATION
When locating vent termination, it is impor- tant to observe the minimum clearances shown in Figure 8, page 6. You will avoid extra framing by positioning your fireplace against an already existing framing mem- ber. The sides of the fireplace may be posi- tioned directly against combustible walls.
*Check with local codes or with the current CAN/CGA B149 [.1 or .2] Installation Codes for Canada or the USA Installations follow the current National Fuel Gas Code, ANS Z223.1, also known as NFPA 54.
Continued
105982 | 5 |