24
OPERATING FIREPLACE
Normal Lighting Instructions To Turn Off Gas To Appliance
OPERATING FIREPLACE
Continued
NORMAL LIGHTING INSTRUCTIONS
WARNING: You must operate this heater with the fireplace screen in place. Make sure fireplace screen is in place before running heater.
NOTICE: During initial operation of new heater, burning logs will give off a
1.STOP! Read the safety information, page 23, column 2.
2.Make sure equipment shutoff valve is fully open.
3.Wait five (5) minutes to clear out any gas. Smell for gas around heater and near floor. If you smell gas, STOP! Fol- low “B” in the safety information on warnings plate. If you don’t smell gas, go to the next step.
A. Using Supplied Wall Switch
1.Set manual ignition bypass switch on the control panel to the OFF position (automatic ignition position).
2.Press ON/OFF button. Hold for 6 seconds. Gas valve will open and electronic ignition will begin sparking to light pilot. LED will light. Note: You may be running this heater for the first time after connecting to gas supply or at the start of your heating season. If so, the ON/OFF button may need to be pressed again. This will allow air to bleed from gas system. If several attempts to light pilot fail, contact a qualified service person or gas supplier for repairs. Until repairs are made, light and operate manually (see Manual Lighting Instructions for Electric Power Outage, page 26).
3.When pilot flame is lit, the thermocouple is heated by the flame. When thermocouple becomes hot (5 to 15 seconds), main burner will automatically light on high flame.
4.To lower flame, push HI/LO button on wall switch once. Note: This fireplace does not have a
CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.
Manual Ignition Bypass Switch (Up is for Remote Control)
| MANUAL |
|
| IGNITION | ON/OFF Button |
HI/LO |
| |
|
| |
Button | ON OFF | Wall |
HI LO | ||
|
| Switch |
| LED |
|
Figure 51 - Control Locations
Manual Ignitor |
| Manual Ignitor | ||
Electrode | Automatic | Pilot | Electrode | Automatic |
| ||||
Pilot | Ignitor | Burner |
| Ignitor |
Burner | Electrode |
|
| Electrode |
Figure 52 - Pilot (Natural Gas) Figure 53 - Pilot (Propane/LP Gas)
B. Using
1.Set manual ignition bypass switch on control panel to OFF position (automatic ignition position).
2.Wait five (5) minutes to clear out any gas. Smell for gas around heater and near floor. If you smell gas, STOP! Fol- low “B” in the safety information on warnings plate. If you don’t smell gas, go to the next step.
3.Point remote control toward the lower front of fireplace and push both buttons at the same time. Hold for 6 sec- onds. The gas valve will open and electronic ignition will begin sparking to light the pilot. Note: You will be able to hear a clicking sound during this process. LED on wall switch will light.
Note: You may be running this heater for the first time after connecting to gas supply or at the start of your heat- ing season. If so, the ON button may need to be pressed again. This will allow air to bleed from gas system. If sev- eral attempts to light pilot fail, contact a qualified service person or gas supplier for repairs. Until repairs are made, light and operate manually (see Manual Lighting Instruc- tions for Electrical Power Outage, page 25).
4.When pilot flame is lit, the thermocouple is heated by the flame. When thermocouple becomes hot (5 to 15 seconds), main burner will automatically light on high flame.
5.To lower flame, point remote control toward lower front of fireplace and push HI/LO button once.
Note: This fireplace does not have a
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater - Wall Switch
Push ON/OFF button on wall switch once.
Shutting Off Heater - Wireless Remote Control
Point remote control toward lower front of fireplace and push both buttons at the same time.
For
.
.com
