Desa VP1000BTA VN10A, VP10A installation manual Operating Heater, Lighting Instructions

10

INSTALLATION

Checking Gas Connections (Cont.)

Operating Heater (Manual Control Blue Flame Models)

For Your Safety Read Before Lighting

Lighting Instructions

INSTALLATION

Continued

3.Check all joints from gas meter for natural or propane/LP supply to equipment shutoff valve (see Figure 17 or 18). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

4.Correct all leaks at once.

Pressure Testing Heater Gas Connections

1.Open equipment shutoff valve (see Figure 14, page 9).

2.Open main gas valve located on or near gas meter for natural gas or open propane/LP supply tank valve.

OPERATING HEATER

MANUAL CONTROL BLUE FLAME

MODELS

FOR YOUR SAFETY READ

BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

3.Make sure control knob of heater is in the OFF position.

4.Check all joints from equipment shutoff valve to control valve (see Figures 15 and 16). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Light heater (see Operating Heater pages 10 through 14). Check the rest of the internal joints for leaks.

7.Turn off heater (see To Turn Off Gas to Appliance, pages 11, 12 or 14, depending on your model).

A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•	Do not try to light any appliance.
•	Do not touch any electric switch; do not use any phone in
	your building.
•	Immediately call your gas supplier from a neighbor’s

8.Replace front panel.

Gas

Meter

Control Valve Location

Equipment

Shutoff Valve

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire de-

partment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by

hand, don’t try to repair it, call a qualified service techni-

cian or gas supplier. Force or attempted repair may result

in a fire or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance and to replace any part of the control system and

any gas control which has been under water.

LIGHTING INSTRUCTIONS

Figure 15 - Checking Gas Joints for Natural Gas

Propane/LP
Supply Tank	Control
	Valve Location

Equipment

Shutoff Valve

Figure 16 - Checking Gas Joints for Propane/LP Gas

1.STOP! Read the safety information above.

2.Make sure equipment shutoff valve is fully open.

3. Turn control knob clockwise Clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information, above. If you don’t smell gas, go to the next step.

5.Press in control knob and turn counterclockwise C-clockwiseto the PILOT position. Keep control knob pressed in for five (5) seconds (see Figure 17, page 11).

Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will al- low air to bleed from the gas system.

•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

For morevisit www..com

110720-01A