Venting Installation
instructions
Continued
Horizontal Termination Configurations
Figures 14 through 18 show different configurations and alterna- tives for venting with horizontal termination. Each figure includes a chart with critical minimum and maximum dimensions which MUST be met. IMPORTANT: If using a venting configuration of only horizontal venting with no vertical run, a 1/4" rise for every 12" of run toward the termination is required.
WARNING: Never run vent downward as this may cause excessive temperatures which could cause a fire. Operation of improperly installed and maintained venting system could result in serious injury, property damage or loss of life.
GROUND FLOOR INSTALLATION
Recommended Applications:
•Installation using cabinet surrounds
•Through the wall using round or square termination (up to 12" horizontal pipe)
•NOT FOR CORNER INSTALLATION
Adjustable | 45° Elbow |
Pipe 12" Max. |
|
Horizontal High
Wind Square
Termination
Wall Firestop 
Square Termination
|
|
|
|
| Vertical (V) |
| Horizontal (H) | ||||||||||||||
32" Series |
|
| 29" min. |
|
|
|
|
| 17" max. | ||||||||||||
36" Series |
|
| 32" min. |
|
|
|
|
| 17" max. | ||||||||||||
45° Elbow |
|
|
| Exterior Portion of | |||||||||||||||||
|
|
|
|
|
|
| |||||||||||||||
Wall |
|
|
| Wall Firestop (Round | |||||||||||||||||
|
|
| Termination Only) | ||||||||||||||||||
Firestop |
|
|
| ||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CORNER AND ALTERNATE INSTALLATION
Recommended Applications:
•Corner ground floor installation
•Ground floor installation where pipe vents horizontally through wall (over 12" horizontal pipe)
•Basement installation where one foot clearance from ground to termination is possible
| Not to Exceed | 90° Elbow |
| (H) Limits | |
Wall |
| |
|
| |
Firestop |
| As Required for (V) |
|
| |
|
| See Chart for Pipe |
|
| Section Required |
Square |
|
|
Termination | 45° |
|
|
| |
| Elbow |
|
Vertical (V) | Required |
|
| Horizontal (H) | ||||||||
32" | 36" | Vertical Pipe | (32"/36") | |||||||||
*401/2" min. | 431/4" min. | None |
|
|
| 30" max. | ||||||
511/2" min. 541/4" min. | 1 ft. |
|
|
| 48" max. | |||||||
631/2" min. 661/4" min. | 2 ft. |
|
|
| 60" max. | |||||||
751/2" min. 781/4" min. | 3 ft. |
|
|
| 84" max. | |||||||
871/2" min. 901/4" min. | 4 ft. |
|
|
| 20' max. | |||||||
*Note: Ground Floor Corner Venting |
|
|
|
|
| |||||||
| Not to Exceed |
|
|
|
|
| ||||||
| (H) Limits |
|
|
|
| Square | ||||||
|
|
|
|
|
|
|
|
|
|
|
| |
| 90° Elbow |
|
|
|
|
|
|
|
|
|
| Termination |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wall |
|
Firestop | 12" Minimum |
45° Elbow
| Round | Figure 15 - Horizontal Termination Configuration for Corner |
Slide Ring | Termination | Installation Using One 90° Elbow |
Over Elbow | Cap |
|
|
|
to Complete Connection
Round Termination
(Kit HTK Shown)
Figure 14 - Horizontal Termination Configuration for Square
and Round Terminations
10 | www.desatech.com |
