Fireplace Installation

Continued

3.Place the blower against the lower rear wall of the firebox outer wrapper with the exhaust port directed upward. The blower will fit inside the back opening and be held in position against the back wall by the magnets (see Figure 25).

4.Be certain that all wire terminals are securely attached to ter- minals on blower motor and that the screw retaining the green ground wire is tight.

5.Mount speed control box to switch bracket by placing the plastic control shaft forward through the opening in the switch bracket (see Figure 26).

6.While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until it is tight against front panel. Place control knob provided on shaft.

7.Turn on power to duplex outlet if previously turned off per the warning in column 2, page 14.

8.Plug in blower power cord.

a.If your firebox is installed as a freestanding unit with an accessory mantel, determine whether the power cord will exit the left side or the right side of the firebox. Route power cord through exit hole and plug the power cord into a wall receptacle near the firebox.

b.If your firebox installation is recessed and/or pre-wired, plug the power cord into the duplex outlet provided. Refer to your firebox owner’s manual for instructions on wiring the duplex outlet.

CAUTION: Never touch the blower wheel while in operation.

9.Check to make sure that the power cord is completely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and check for operation. Turn blower off by turning knob fully counterclockwise before continuing.

10.Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front of the blower (see Figure 27).

 

 

Blower

 

 

Location

 

Lower Firebox

 

 

Cavity

 

Side View

Spade

 

 

Magnetic

 

Terminals

 

 

Strips

Exhaust

Port

Green

Ground Wire

Screw

Figure 25 - Blower Model BK

Switch

Speed Control

Bracket

 

 

 

Blower

 

Plug-In

 

 

Duplex Outlet (Located

Locknut

 

underneath firebox

Control Shaft

floor against lower right

Control Knob

outside wall)

 

Figure 26 - Attaching Speed Control to Firebox

Wiring Diagram Decal

12" in Front of Blower

Figure 27 - Location of Wiring Diagram Decal (Model May

Vary From Illustration)

Model BKT Installation

Note: When installing the BKT thermostatically-controlled blower, you must first secure the thermal switch bracket to the blower if it has not already been factory installed.

1. Place the green ground wire with ring terminal between the bottom hole on the thermal switch bracket and the top ear hole on the blower assembly. Insert the Phillips screw into all three pieces and tighten securely (see Figure 28, page 16).

2. Connect wire harness and power cord terminals. Connect the blue jumper wire to the blower motor terminal and the right side terminal of the thermal switch. Connect the black wire to the left side of the thermal switch and the white wire to the other remaining blower motor terminal.

Note: The power cord outer insulation sleeve may have to be stripped slightly to allow enough wire length to reach and make all connections. DO NOT trim excessive length away. Just enable enough to make all connections securely.

108860-01D

www.desatech.com

15

Page 15
Image 15
Desa (V)T32EN installation manual Model BKT Installation, Blower Model BK

(V)T32EN specifications

Desa (V)T32EN is a cutting-edge vehicle designed to meet the growing demands of modern transportation while ensuring efficiency, safety, and sustainability. This remarkable vehicle is the embodiment of innovative engineering and advanced technology, making it a key player in both the commercial and personal vehicle sectors.

One of the standout features of the Desa (V)T32EN is its powerful and efficient powertrain. The vehicle is equipped with a state-of-the-art engine that incorporates hybrid technology, allowing it to seamlessly switch between electric and gasoline modes. This flexibility not only helps reduce emissions but also provides impressive fuel efficiency, making it ideal for long-distance travel or urban commuting. The hybrid system is complemented by regenerative braking, which captures energy during braking and feeds it back into the vehicle’s battery, enhancing overall efficiency.

Another significant characteristic of the Desa (V)T32EN is its advanced safety features. The vehicle is designed with a robust safety framework that includes a suite of sensors and cameras for 360-degree awareness. This technology enables features such as automatic emergency braking, lane departure warning, and adaptive cruise control, ensuring a safer driving experience for both the driver and passengers. Additionally, the vehicle includes a reinforced chassis that meets high safety standards, providing peace of mind on the road.

In terms of comfort and convenience, the Desa (V)T32EN excels with its spacious interior and modern infotainment system. The cabin is thoughtfully designed, providing ample legroom and storage options. The infotainment system features a large touchscreen display that integrates seamlessly with smartphones, allowing for hands-free operation of navigation, music, and communication apps. Furthermore, climate control and adjustable seating settings enhance the overall driving experience, making long journeys enjoyable.

Technological sophistication extends to the vehicle’s connectivity features. The Desa (V)T32EN boasts advanced connectivity options that allow for real-time updates on traffic, weather, and vehicle performance. With built-in Wi-Fi and mobile app integration, users can stay connected to the digital world while on the move.

In conclusion, the Desa (V)T32EN is not just a vehicle; it represents the future of transportation. Its combination of hybrid technology, advanced safety features, and user-friendly connectivity makes it a formidable contender in the automotive landscape. As consumers increasingly prioritize sustainability and safety, the Desa (V)T32EN stands out as a leading option that aligns with these values, ensuring it meets the diverse needs of today’s drivers.