English
MAINTENANCE
Brushes (Fig. 18)
CAUTION: Turn off and unplug the tool before mak- ing any adjustments or removing or installing attach- ments or accessories. Be sure the switch is in the OFF position.
Inspect carbon brushes regularly by unplugging tool, removing the brush cap (OO) and withdrawing the brush assembly. Keep brushes clean and sliding freely in their guides. Always insert a replacement brush in the same ori- entation in the holder as the used brush was prior to its removal. Carbon brushes have varying symbols stamped into their sides, and if the brush is worn down to the line closest to the spring, brushes must be replaced. Use only identical DEWALT brushes. Use of the correct grade of brush is essential for proper operation. New brush assem- blies are available at DEWALT service centers. The tool should be allowed to “run in” (run at no load) for 10 minutes before use to seat new brushes.
Transportation and Storage
The rear water attachment (G), cutting cart water attach- ment (I) and water pan (K) may be nested together to make carrying easier (Fig. 19).
The edge guide (J) and the cutting cart extension (PP) may also be stored in the underside of the water pan (Fig. 20).
Cleaning
1.Insert the water pump into a bucket of clean water and pump the water through the hose system.
2.Turn off and unplug the saw from the power supply.
3.Place a 5 gallon bucket under the drain plug. Remove the drain plug and allow the water to empty into the bucket.
4.Slide the cutting cart off the rail system. Spray the cut- ting cart with a hose or wipe with a grout sponge or rag.
5.Wipe the rails, motor housing, and support arm with a grout sponge or a rag. Spray lubricants are not required on the guide rail or wheels.
6.Clean the water pan by spraying with a hose or wiping with a grout sponge.
Use only mild soap and a damp cloth to clean the tool. Many household cleaners contain chemicals which could seriously damage plastic. Also, do not use gasoline, tur- pentine, lacquer or paint thinner, dry cleaning fluids or sim- ilar products. Try not to let any liquid get inside the tool; never immerse any part of the tool into a liquid.
Lubrication
WARNING: NEVER spray or in any other way apply lubricants or cleaning solvents inside the tool. This can seriously affect the life and performance of the tool and may result in personal injury.
DEWALT tools are properly lubricated at the factory and are ready for use. However, it is recommended that, once
FIG. 19
TOP
K
FIG. 20
BOTTOM
J
FIG. 21
D24001
a year, you take or send the tool to a certified service cen- ter for a thorough cleaning and inspection.
GRepairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized serv- ice centers or other qualified service organizations, always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are avail- able at extra cost from your local dealer or authorized serv- ice center.
CAUTION: The use of any other accessory not recom- mended for use with this tool could be hazardous.
| STAND D24001 (FIG. 21) |
|
|
|
I | CUTTING WHEELS: | 7" | Ceramic | DW4760 |
| 10" | Ceramic | DW4761 | |
|
| |||
|
| 10" | Porcelain DW4762 | |
If you need assistance in locating any accessory for your tool, contact: DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
Three Year Limited Warranty
PPDEWALT will repair, without charge, any defects due to
faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of war- ranty coverage and warranty repair information, visit www.dewalt.com or call
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.
FREE WARNING LABEL REPLACEMENT: If your warn- ing labels (also refer to pages 3, 4) become illegible or are missing, call
10
