D s, Debug signal breakout header LEDs | Digi 90000797_A specification

A B O U T T H E D E V E L O P M E N T B O A R D

. . .

LEDs.

.

L E D s

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LEDs: DS3-DS7

LED DS1

LED DS2

Debug (signal) breakout header LEDs

The switching regulator is adjusted to output +3.3VDC ± 5% or better. LED DS1 lights up when the regulator outputs +3.3V power. See “Power supply” on page 21 for more information.

LED DS2 lights up when the host system supplies power over the USB bus. This LED indicates that the host platform has recognized the attachment of a USB peripheral device on the USB bus. See “USB peripheral interface, J4” on page 23 for more information.

Five LEDs are associated with the debug breakout header (J4):

DISABLE, DS3: Lights up when the W_DISABLE# signal is asserted.

RST, DS4: Lights up when the RESET# signal is asserted.

WAN, DS5: Reserved for future use.

LAN, DS6: Lights up when the module drives the LED_WLAN# signal.

PAN, DS7: Reserved for future use.

See “Debug breakout header, P21” on page 24 for more information.

www.digiembedded.com

19

Image 17

Digi 90000797_A manual D s, Debug signal breakout header LEDs

Contents

Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B G i i n f o r m a t i o n UpdatesRelated Documentation To contact Digi International by Use Contact information A t u r e s About the Module A t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connector Pin Type Wlan Mini Card Signal Digi Connect Wi- Wave module edge connector Pinout 2 1 b / g m o d e s a n d c h a n n e l s B p e r i p h e r a l c o n t r o l l e rChannel Allocations Channel Center frequency Frequency spread MHz MHz MHz L t a g e m o n i t o r R e s e t g e n e r a t o r L t a g e r e g u l a t o r s W e r A t ’ s o n t h e d e v e l o p m e n t b o a r d Features Development board Unpopulated components Digi Connect Wi-Wave module connector, J52 No connect or Jtagtdi Vcc3.3 Pin Type Signal D s Debug signal breakout header LEDs Alternative methods to trigger I t c h e s a n d r e s e t f u n c t i o n a l i t y W e r s u p p l y Input power jack, J3 Input power supply Jtag breakout Header signal mapA G B r e a k o u t H e a d e r , P 2 B p e r i p h e r a l i n t e r f a c e , J B u g b r e a k o u t h e a d e r , P 2 Debug breakout Header signal mapSignal FL cables FL connectorsL a n d R P S M a c o n n e c t o r s RP-SMA connectors For more information Necessary Conditions for Integration Using the Antenna Connect Wi-Wave antenna configurations Dimensions T e n n a Specification s 2 d B i D i p o l eN e r a l i n f o r m a t i o n Attributes Antenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram Attribute Band T e n n a Specification s 5 d B i D i p o l e Color Freq MHz Peak dBi Angle o Avg dBi Radiation pattern H-Plane 2.0 and 5.0 GHz Radiation pattern E-plane 2.0 and 5.0 GHz C h a n i c a l d i m e n s i o n s V i r o n m e n t a l Specification s E x p o s u r e s t a t e m e n t W e r r e q u i r e m e n t sF e t y s t a t e m e n t s Parameter Limits Module Dimensions Development Board dimensions C P a r t 1 5 C l a s s B Appendix BCertifications Modifications FCC Declaration of Conformity Standards International EMC Standards Index Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008